Question 1

How does the Car Mirror's power function operate, and what steps are involved in testing and replacing the Car Mirror power switch on Mitsubishi Lancer?

Accepted Answer

A power mirror employs two small motors for operational capabilities. One controls the horizontal movement while another handles the vertical movement. Then, polarity changes allow for each motor to rotate in the opposite direction. Utilizing a single switch, the multi-functional switch assembly located on the dashboard is capable of controlling both left and right mirrors. To begin checking the system, remove the power mirror switch first. Next, with the ignition ON, check for battery power at the indicated wires. If no voltage is found, trace the fault using wiring diagrams. Guarantee earth continuity at black wire and carry out repairing procedure. To access the mirror wiring, remove the mirror trim or door trim panel, then disconnect the driver's side mirror wiring. Test with a lamp between the appropriate wires and ensure the selector lever is pointing to the mirror being tested. The test lamp comes on when the switch is moved left or right. If an LED is being used in either direction, check both by swapping leads. During the testing for up and down movement, if the lamp does not illuminate during any checks, replace the power mirror switch. For the CE models check the continuity between the specific wires. For the CG and the CH model carry out similar continuity checks. Offer mirror replacement if open circuit is found. Remove the power mirror switch from the dashboard by wrapping a screwdriver in cloth and carefully prying the switch from the dashboard. After that disconnect the wiring and pull the switch out. Finally, install the switch by reversing the removal process.

Question 2

How to remove and install front Car Mirror, Door Lock, Door Lock Cylinder, Exterior Door Handle, Interior Door Handle and Window Regulator on Mitsubishi Lancer?

Accepted Answer

To remove / install the interior handles, trim panel and sealing sheet on CE models, with the regulator handle engage the washer is pushed away. Then withdraw the handle retaining clip with a wire hook, and remove the handle and washer. For power windows, remove the retaining screw within the pull handle. Carefully prise the switch panel from the door trim using a cloth-covered screwdriver. Disconnect the wiring and withdraw the switch panel. On the passenger's side, it's not necessary to remove this. After that, take out the retaining screw in the pull handle cavity and pull out the pull handle, then take out the retaining screw from the inner handle trim and pull out the trim. With utmost care, remove the cover from the screw at the front of the door trim. Then undo the screw. Take note that for a sedan model, there's another screw at the back of the trim above the door lock. To remove the trim panel, grasp its lower outside edge and pull it away from the door to disengage the retaining clips. Next, lift the trim panel up and withdraw it. If working on the passenger's side of a model with power windows, disconnect power window switch wiring before removing trim panel. After removing the retaining screws, the pull handle bracket is withdrawn. After that, remove the retaining screws of the interior handle and carefully peel off the plastic sheet from the door by cutting the sealant. If required, feed the wiring connector through and then remove the sealing sheet from the door. Store it flat and with the sealant-side facing up. If necessary, release the clips that hold the control rods to the interior handle. Remove the handle. The process of installation is just the reverse of that of removal and entails ensuring that the sealing sheet is correctly positioned, the sealant remains in operable condition, replacing any damaged trim panel retaining clips, and tightening all screws securely. The CG and CH models start the same way: the switch panel and pull handle are removed. Next, the interior handle trim and the trim panel are removed. If the model is equipped with power windows, the power window switch wiring must be disconnected. The window glass removal entails positioning of the glass to expose the retaining screws, temporally installing the window regulator handle or connecting of power window switch wiring so the glass can be moved as required, loosening of screws retaining the glass to the regulator slide, tilting the glass up and by maneuvering it through the door opening. To install the window, one must follow the steps in reverse to ensure it is seated properly and operates properly before putting the sealing sheet and trim panel back on. To service each window regulator, remove the trim panel, sealing sheet, window glass, if applicable disconnect the wiring of power window motor, if applicable remove the retaining bolts and move out the regulator assembly from the door and lubricate the sliding surfaces before refitting. Removing the exterior handle and lock cylinder requires that the window (which we can assume is the window of a car) be raised. Subsequently, the trim panel must first be removed, control rods disconnected, and the handle and lock cylinder removed. With everything on the right place, the exterior handle and lock cylinder will operate properly. The door lock removal consists of disconnecting control rods and wiring;after removing retaining screws grease sliding parts before reinstalling. Mark the position of the lock striker, remove retaining screw, and reinstall an aligned position. To renew mirror glass, adjust mirror and disengage spring or clips if necessary, next remove mirror cover and the surrounding panel if applicable, disconnect power mirror wiring, remove retaining screws or nuts, finally reinstall and test mirror operation.

Genuine Mitsubishi Lancer Car Mirror

14 Car Mirrors found

Mitsubishi Lancer Mirror Assembly, Passenger Side Gray Part Number: MN126376HD

Mitsubishi Lancer Mirror Assembly, Passenger Side Part Number: 7632A094

Mitsubishi Lancer Mirror Assembly, Driver Side Part Number: 7632A093

Mitsubishi Lancer Mirror Assembly, Driver Side Part Number: 7632A095

Mitsubishi Lancer Mirror Assembly, Passenger Side Part Number: 7632A096

Mitsubishi Lancer Mirror Assembly, Passenger Side Part Number: 7632C368

Mitsubishi Lancer Mirror Assembly, Driver Side Part Number: 7632C367

Mitsubishi Lancer Mirror Assembly, Driver Side Part Number: MN126377

Mitsubishi Lancer Mirror Assembly, Driver Side Part Number: MN126373

Mitsubishi Lancer Mirror Assembly, Driver Side Part Number: MR959855

Mitsubishi Lancer Mirror Assembly, Passenger Side Blue Part Number: MN126376BC

Mitsubishi Lancer Mirror Assembly, Driver Side White Part Number: MN126375WC

Mitsubishi Lancer Mirror Assembly, Driver Side Gray Part Number: MN126375HD

Mitsubishi Lancer Mirror Assembly, Passenger Side Part Number: MN126378

Mitsubishi Lancer Car Mirror

Mitsubishi Lancer Car Mirror Parts Questions & Experts Answers

Related Mitsubishi Lancer Parts

Browse by Year