How to remove and install the Hood on Mitsubishi Lancer?

To remove and install the Hood, first lift the Hood and place covers on both front mudguards and a heavy cloth behind each rear corner to prevent damage. To make installation easier, mark around the hinge plate with a lead pencil. To do this task you will require essential tools such as T15 torque bits, 10mm socket, and Phillips screwdriver. Lifting the Hood Disconnect the windscreen washer hose from the connector in the Hood's center. Remove the bolts retaining the hinges. With assistance, lift the Hood clear of the vehicle. For installation of hood, make sure to line up the marks made earlier, install and tighten retaining bolts and slowly shut the hood while checking for proper alignment and adjusting as needed. If necessary, adjust the height of the front Hoods by turning the rubber bump stops to align with the body. Check the Hood lock to ensure that it pops the Hood up when released. To adjust Hood horizontally, loosen the hinge retaining bolts to move the Hood so it is evenly spaced from adjacent panels. In order to facilitate the removal and installation of the Hood lock, remove the grille and front bumper, if any. Remove the retaining bolts on Hood lock assembly, detach cable of lock lever, and withdraw lock from vehicle. The order of reinstallation is reverse and connect the release cable properly. To renew the release cable, remove the Hood lock and splashguard, release the cable from the retainers and withdraw it from the conduit beneath the radiator support panel. Take out the screws holding the Hood release lever inside the vehicle, push it forward and pull it out. Gently pull the wire through the firewall grommet and withdraw the assembly. To install, put the release cable in the grommet hole, install the release lever and tighten the screws, feed the cable through the conduit and install the Hood lock.

Genuine Mitsubishi Lancer Hood

Engine Hood

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Hoods found

View related parts
Mitsubishi Lancer Hood Part Number: 5900A209
$497.72 MSRP: $703.00
You Save: $205.28 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Mitsubishi's factory warranty.
Fits the following Vehicles:
- 2016-2017, 2008-2012 Mitsubishi Lancer | DE, ES, ES Sportback, GT, GT Sportback, GTS, GTS Sportback, Ralliart, Ralliart Sportback, SE, SEL | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View related parts
Mitsubishi Lancer Hood Part Number: 5900A157
$524.89 MSRP: $741.37
You Save: $216.48 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Mitsubishi's factory warranty.
Fits the following Vehicles:
- 2002-2003 Mitsubishi Lancer | ES, LS, OZ Rally | 4 Cyl 2.0 L GAS
View related parts
Mitsubishi Lancer Hood Part Number: 5900A586
$628.67 MSRP: $819.65
You Save: $190.98 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Mitsubishi's factory warranty.
Fits the following Vehicles:
- 2011-2015 Mitsubishi Lancer | DE, ES, ES Sportback, GT, GT Sportback, Ralliart, Ralliart Sportback, SE | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View related parts
Mitsubishi Lancer Hood Part Number: 5900A138
$642.01 MSRP: $837.04
You Save: $195.03 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Mitsubishi's factory warranty.
Fits the following Vehicles:
- 2004-2007 Mitsubishi Lancer | ES, LS, OZ Rally, Ralliart, SE, Sportback, Sportback Ralliart | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View related parts
Mitsubishi Lancer Hood Part Number: 5900A244
$865.07 MSRP: $1127.85
You Save: $262.78 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Mitsubishi's factory warranty.
Fits the following Vehicles:
- 2008-2015 Mitsubishi Lancer | Evolution GSR, Evolution MR, Evolution MR Touring, Evolution SE, Ralliart, Ralliart Sportback | 4 Cyl 2.0 L GAS
View related parts
Mitsubishi Lancer Hood Part Number: 5900A210
$1136.91 MSRP: $1482.27
You Save: $345.36 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Mitsubishi's factory warranty.
Fits the following Vehicles:
- 2003-2006 Mitsubishi Lancer | Evolution, Evolution MR, Evolution RS, Evolution SE | 4 Cyl 2.0 L GAS

Mitsubishi Lancer Hood

Mitsubishi Lancer Hood is a hinged cover that protects the engine bay from the rain, dust, or any other external particles. More importantly, the Hood also opens to allow hassle-free access for regular under-bonnet duties. The exterior smoothness of the Mitsubishi car directs airflow across the front to maintain the designed aerodynamic characteristic. By the choice of strong construction materials, strength and reliability are promoted, and with the right application, the Hood aligns with the surrounding body lines for a model year. Finish options explicitly available are two options. A primer-coated panel comes ready for a custom paint, allowing owners to match existing schemes without surface preparation. An alternative that is often made from fiberglass to lower the mass of the panel so that it is easier to lift and which provides weatherproofing is a gelcoat finish. No matter the finish, the Hood will be the same dimensions as an opening of a Mitsubishi passenger compartment to firmly secure and close flush with adjacent fenders and grille components. The meticulous fit ensures that there is no vibration, wind noise, and that styling continuity is maintained as seen on the Lancer nameplate throughout its bodywork. The Mitsubishi Lancer Hood is a vital exterior panel that combines environmental protection, aerodynamic sculpting, and easy service access on a Lancer vehicle. Furthermore, it serves as a visually unifying element on every Mitsubishi Lancer.

OEM Hood can boast superior quality and long-term durability. Each part meets strict factory specs and passes careful checks in production. So you'll get Hood with long-lasting strength and an exact fit. If you need OEM Mitsubishi Lancer Hood, the online store is the ideal place. The store carry a wide range of genuine Mitsubishi Lancer parts at the highly competitive prices. You'll enjoy a simple and no-hassle shopping experience. You'll get unbeatable prices and fast delivery service. You'll get the manufacturer's warranty and a straightforward return policy. Shop with confidence and keep your car in top condition.

Mitsubishi Lancer Hood Parts Questions & Experts Answers

Hood
5900A138
Q: How to remove and install the Hood on Mitsubishi Lancer?
A:
To remove and install the Hood, first lift the Hood and place covers on both front mudguards and a heavy cloth behind each rear corner to prevent damage. To make installation easier, mark around the hinge plate with a lead pencil. To do this task you will require essential tools such as T15 torque bits, 10mm socket, and Phillips screwdriver. Lifting the Hood Disconnect the windscreen washer hose from the connector in the Hood's center. Remove the bolts retaining the hinges. With assistance, lift the Hood clear of the vehicle. For installation of hood, make sure to line up the marks made earlier, install and tighten retaining bolts and slowly shut the hood while checking for proper alignment and adjusting as needed. If necessary, adjust the height of the front Hoods by turning the rubber bump stops to align with the body. Check the Hood lock to ensure that it pops the Hood up when released. To adjust Hood horizontally, loosen the hinge retaining bolts to move the Hood so it is evenly spaced from adjacent panels. In order to facilitate the removal and installation of the Hood lock, remove the Grille and front Bumper, if any. Remove the retaining bolts on Hood lock assembly, detach cable of lock lever, and withdraw lock from vehicle. The order of reinstallation is reverse and connect the release cable properly. To renew the release cable, remove the Hood lock and splashguard, release the cable from the retainers and withdraw it from the conduit beneath the radiator support panel. Take out the screws holding the Hood release lever inside the vehicle, push it forward and pull it out. Gently pull the wire through the firewall grommet and withdraw the assembly. To install, put the release cable in the grommet hole, install the release lever and tighten the screws, feed the cable through the conduit and install the Hood lock.