How to remove and install the steering gear assembly on the Front Cross-Member with an airbag on Mitsubishi Lancer?

To take off and install, First, disconnect the negative battery terminal on airbag-equipped models (and wait at least 60 seconds to disable it). Make sure the ignition key is removed and steering wheel is locked straight ahead. When removing the steering gear assembly from vehicles with an airbag, engage the steering lock. The steering cannot then be moved further than its normal locked position, otherwise the clock spring will be damaged. For CG and CH model vehicles, quickly dry paint the relationship between the intermediate shaft and steering gear, and remove the pinch bolt and washer to separate them. Securely elevate the front of the vehicle on jack stands and detach the front tires. Next, extract both sides' stabiliser bar link nut and bolt and their respective washers, bushes and spacer tube and note the order of removal. Remove the bolts retaining the control arm rear pivot bush brackets to the crossmember and withdraw these brackets. Lower the control arms, using wire to hold them in position, to avoid strain on the ball joints. Loosen the castellated nut that secures the tie rod end to the steering knuckle on both sides. Note that on some models there is a self-locking nut in place of the castellated nut and it must be discarded when removed. Remove the tie rod ends from the steering knuckles by means of a ball joint separator or by striking the knuckle with a hammer. Detach and remove the bolts securing the steering gear to the crossmember. Pull the steering gear away and suspend it with wire, if possible. On models CG and CH, the steering gear is lowered with the crossmember. Detach the engine pipe along with the front and rear engine mounting through bolts. Remove the bolts retaining the centre member and withdraw it while someone steadies the engine. Lower the crossmember; manoeuvre across and out from under the vehicle. For CG and CH models, disconnect hydraulic lines from the power steering gear before lowering the crossmember with the steering gear. Putting the installation back on the car is basically the reverse of the removal process. Follow the steps outlined and remember to check the crossmember for damage and renew accordingly. Check stabiliser bar bushes, which are on the bracket and bolts, and tighten correctly. During mounting, don't cause damage of the steering gear boots. For CE models, the steering gear retaining bolts should be torque to situation. For CG and CH Models firstly mount the steering gear properly. Then raise the crossmember and guide the intermediate shaft into the firewall cavity. When the gear is high enough fit and tighten the power steering hoses. Tighten the control arm rear pivot bush bracket bolts then install front pivot bolt loosely. Install stabiliser bar link components in noted order and tighten retaining nut. Attach the center member, tightening the retaining bolts, then take the front wheels back on and lower the vehicle, bouncing the front to stabilise suspension and lightly settling the bushes making sure to then tighten the front control arm pivot bolt, and finally securely connect the battery terminal on models with airbag.

Genuine Mitsubishi Front Cross-Member

Front Engine Cross Member

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

159 Front Cross-Members found

View related parts
Mitsubishi Outer Rail, Driver Side Part Number: 5220BA89
$237.52 MSRP: $335.48
You Save: $97.96 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sidemember, Front Outer Left-Hand; Front Cross-Member
- Position: Driver Side
Fits the following Mitsubishi Models:
- Outlander | 2022-2025 | Black Edition, ES, SE, SE Launch Edition, SEL, SEL Launch Edition | 4 Cyl 2.5 L GAS
- Outlander PHEV | 2023-2025 | ES, Platinum Edition, Ralliart, SE, SE Tech, SEL, SEL Premium, SEL Touring | 4 Cyl 2.4 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Mitsubishi Floor Rail, Passenger Side Part Number: 751A4W060P
$238.99 MSRP: $337.55
You Save: $98.56 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sidemember, Front Floor, Right-Hand; Front Cross-Member
- Position: Passenger Side
- Replaces: 5253CT30
Fits the following Mitsubishi Models:
- Outlander PHEV | 2023-2025 | ES, Platinum Edition, Ralliart, SE, SE Tech, SEL, SEL Premium, SEL Touring | 4 Cyl 2.4 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Mitsubishi Inner Panel, Passenger Side Part Number: 5253B340
$243.65 MSRP: $344.13
You Save: $100.48 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sidemember, Front Inner Right-Hand; Front Cross-Member
- Position: Passenger Side
Fits the following Mitsubishi Models:
- Lancer | 2003-2006 | Evolution, Evolution MR, Evolution RS, Evolution SE | 4 Cyl 2.0 L GAS
View related parts
Mitsubishi Floor Rail, Driver Side Part Number: 5253CT29
$248.70 MSRP: $351.27
You Save: $102.57 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sidemember, Front Floor, Left-Hand; Front Cross-Member
- Position: Driver Side
Fits the following Mitsubishi Models:
- Outlander PHEV | 2023-2025 | ES, Platinum Edition, Ralliart, SE, SE Tech, SEL, SEL Premium, SEL Touring | 4 Cyl 2.4 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Mitsubishi Rear Rail, Driver Side Part Number: 5220L105
$248.91 MSRP: $351.57
You Save: $102.66 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sidemember, Front Floor, Left-Hand; Front Cross-Member
- Position: Driver Side
Fits the following Mitsubishi Models:
- Eclipse Cross | 2018-2020 | ES, LE, SE, SEL, SP | 4 Cyl 1.5 L GAS
View related parts
Mitsubishi Inner Rail, Passenger Side Part Number: 5220C560
$256.20 MSRP: $361.87
You Save: $105.67 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sidemember, Front Inner Right-Hand; Front Cross-Member
- Position: Passenger Side
Fits the following Mitsubishi Models:
- Outlander | 2007-2009 | ES, LS, SE, XLS | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mitsubishi Rear Rail, Passenger Side Part Number: 751N8W010P
$261.19 MSRP: $368.92
You Save: $107.73 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sidemember, Front Floor, Right-Hand; Front Cross-Member
- Position: Passenger Side
Fits the following Mitsubishi Models:
- Eclipse Cross | 2022-2025 | Black Edition, ES, LE, Ralliart, SE, SE Special Edition, SEL, SEL Special Edition, SEL Touring | 4 Cyl 1.5 L GAS
View related parts
Mitsubishi Outer Rail, Passenger Side Part Number: 5220BA90
$261.28 MSRP: $369.03
You Save: $107.75 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sidemember, Front Outer Right-Hand; Front Cross-Member
- Position: Passenger Side
Fits the following Mitsubishi Models:
- Outlander | 2022-2025 | Black Edition, ES, SE, SE Launch Edition, SEL, SEL Launch Edition | 4 Cyl 2.5 L GAS
- Outlander PHEV | 2023-2025 | ES, Platinum Edition, Ralliart, SE, SE Tech, SEL, SEL Premium, SEL Touring | 4 Cyl 2.4 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Mitsubishi Inner Rail, Passenger Side Part Number: 5220D148
$261.71 MSRP: $369.65
You Save: $107.94 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sidemember, Front Inner Right-Hand; Front Cross-Member
- Position: Passenger Side
Fits the following Mitsubishi Models:
- Lancer | 2008-2015 | Evolution GSR, Evolution MR, Evolution MR Touring, Evolution SE, Ralliart, Ralliart Sportback | 4 Cyl 2.0 L GAS
View related parts
Mitsubishi Lower Tie Bar Part Number: 5256B724
$265.24 MSRP: $374.64
You Save: $109.40 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Crossmember, Front Panel, LW; Front Cross-Member
Fits the following Mitsubishi Models:
- Mirage G4 | 2017-2020 | ES, LE, RF, SE | 3 Cyl 1.2 L GAS
View related parts
Mitsubishi Lower Rail Assembly, Passenger Side Part Number: 5220C132
$265.50 MSRP: $375.00
You Save: $109.50 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sidemember Assembly, Front Right-Hand; Front Cross-Member
- Position: Passenger Side
Fits the following Mitsubishi Models:
- Eclipse | 2006-2012 | GS, GS Sport, GT, SE, Spyder GS, Spyder GS Sport, Spyder GT, Spyder SE | 4 Cyl 2.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Mitsubishi Inner Rail, Driver Side Part Number: 5220C483
$266.95 MSRP: $377.05
You Save: $110.10 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sidemember, Front Inner Left-Hand; Front Cross-Member
- Position: Driver Side
Fits the following Mitsubishi Models:
- Lancer | 2008-2017 | DE, ES, ES Sportback, GT, GT Sportback, GTS, GTS Sportback, Ralliart, Ralliart Sportback, SE, SEL | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View related parts
Mitsubishi Inner Rail, Passenger Side Part Number: 5220C484
$269.57 MSRP: $380.75
You Save: $111.18 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sidemember, Front Inner Right-Hand; Front Cross-Member
- Position: Passenger Side
Fits the following Mitsubishi Models:
- Lancer | 2008-2017 | DE, ES, ES Sportback, GT, GT Sportback, GTS, GTS Sportback, SE, SEL | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View related parts
Mitsubishi Rail Reinforcement, Driver Side Part Number: 75311W100P
$299.14 MSRP: $422.52
You Save: $123.38 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sidemember, Front Floor; Front Cross-Member
- Position: Driver Side
Fits the following Mitsubishi Models:
- Outlander PHEV | 2025 | ES, Platinum Edition, SE, SEL | 4 Cyl 2.4 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Mitsubishi Rail Reinforcement, Passenger Side Part Number: 75310W070P
$299.14 MSRP: $422.52
You Save: $123.38 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sidemember, Front Floor; Front Cross-Member
- Position: Passenger Side
Fits the following Mitsubishi Models:
- Outlander PHEV | 2025 | ES, Platinum Edition, SE, SEL | 4 Cyl 2.4 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Mitsubishi Inner Rail, Driver Side Part Number: 5220H883
$299.51 MSRP: $423.03
You Save: $123.52 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sidemember, Front Inner Left-Hand; Front Cross-Member
- Position: Driver Side
Fits the following Mitsubishi Models:
- Outlander PHEV | 2018-2022 | GT, LE, SEL | 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 4 Cyl 2.4 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Mitsubishi Lower Rail Assembly, Passenger Side Part Number: 5220G490
$300.14 MSRP: $423.93
You Save: $123.79 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sidemember Assembly, Front Right-Hand; Front Cross-Member
- Position: Passenger Side
Fits the following Mitsubishi Models:
- Mirage | 2017-2024, 2014-2015 | BE, Black Edition, Carbonite Edition, DE, ES, GT, LE, RF, SE | 3 Cyl 1.2 L GAS
- Mirage G4 | 2017-2024 | BE, Carbonite Edition, ES, LE, RF, SE | 3 Cyl 1.2 L GAS
View related parts
Mitsubishi Inner Rail, Passenger Side Part Number: 5220H884
$312.38 MSRP: $441.22
You Save: $128.84 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sidemember, Front Inner Right-Hand; Front Cross-Member
- Position: Passenger Side
Fits the following Mitsubishi Models:
- Outlander PHEV | 2018-2022 | GT, LE, SEL | 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 4 Cyl 2.4 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Mitsubishi Reinforcement Beam Part Number: 5230F515
Product Specifications
- Other Name: Crossmember, Front Deck; Front Cross-Member
Fits the following Mitsubishi Models:
- Outlander Sport | 2014-2015 | ES, GT, SE | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View related parts
Mitsubishi Lower Rail Assembly, Passenger Side Part Number: 5220C100
Product Specifications
- Other Name: Sidemember Assembly, Front Right-Hand; Front Cross-Member
- Position: Passenger Side
Fits the following Mitsubishi Models:
- Galant | 2004-2012 | DE, ES, FE, GTS, LS, Ralliart, SE, Sport Edition, Sport V6 | 4 Cyl 2.4 L GAS, 6 Cyl 3.8 L GAS

| Page 1 of 8 |Next >

1-20 of 159 Results

Mitsubishi Front Cross-Member

The Mitsubishi Front Cross-Member is an important component of the chassis to ensure stiffness and to facilitate the weight transfer of the engine and transmission. That is not all. It also locks suspension points in precise position, which allows every Mitsubishi car to deliver confident balance. Mitsubishi aimed at reliable mobility when it developed the Model A. Its range of cars today all feature smart MIVEC engines, a Super All Wheel Control that grips loose roads, effortless cruise control, and handy smartphone link systems that simplify daily driving for families and new drivers. The company also investigates fuel cell power and hybrid technology to reduce fuel use while retaining user-friendly ownership through ingenious innovation, and this has much more to do with innovations and safety sensors than snazzy features. In line with this philosophy of strength and ease, the Front Cross-Member is a lateral steel beam that is fixed between the main frame rails and forms part of the underbody foundation so that the body, powertrain, and suspension all mount in their correct position. The Front Cross-Member helps keep wheel alignment in order and prolongs the life of your tires by bracing heavy components low and center, which helps it resist twisting as the car brakes hard, hits bumps, and rounds corners. It is a good practice to regularly inspect the towbar for rust, cracks, impact damage, or anything that would cause concern. If this member weakens, the chassis will sag, steering angles will drift, and ride comfort will suffer. The Front Cross-Member is reliable and uncomplicated. Furthermore, it is useful across the range. This is a component that aims for long-lasting stability on any journey.

Pick genuine OEM Front Cross-Member if you want superb performance and durability that lasts. Mitsubishi builds that using high-grade materials and official factory techniques to meet very strict standards. This means you get parts you can actually trust for your daily drive. Finding the right parts is simple in the massive stock of genuine inventory. You can stop guessing if a part will fit or hold up. You will love the low prices, dependable service and the real manufacturer's warranty on Mitsubishi Front Cross-Member. Order today and the store will ship your brand-new items to your door as fast as possible.

Mitsubishi Front Cross-Member Parts Questions & Experts Answers

Sidemember Assembly, Passenger Side
5253B338
Q: How to remove and install the steering gear assembly on the Front Cross-Member with an airbag on Mitsubishi Lancer?
A:
To take off and install, First, disconnect the negative battery terminal on airbag-equipped models (and wait at least 60 seconds to disable it). Make sure the ignition key is removed and steering wheel is locked straight ahead. When removing the steering gear assembly from vehicles with an airbag, engage the steering lock. The steering cannot then be moved further than its normal locked position, otherwise the clock spring will be damaged. For CG and CH model vehicles, quickly dry paint the relationship between the intermediate shaft and steering gear, and remove the pinch bolt and washer to separate them. Securely elevate the front of the vehicle on jack stands and detach the front tires. Next, extract both sides' stabiliser bar link nut and bolt and their respective washers, bushes and spacer tube and note the order of removal. Remove the bolts retaining the control arm rear pivot bush brackets to the crossmember and withdraw these brackets. Lower the control arms, using wire to hold them in position, to avoid strain on the ball joints. Loosen the castellated nut that secures the tie rod end to the steering knuckle on both sides. Note that on some models there is a self-locking nut in place of the castellated nut and it must be discarded when removed. Remove the tie rod ends from the steering knuckles by means of a ball joint separator or by striking the knuckle with a hammer. Detach and remove the bolts securing the steering gear to the crossmember. Pull the steering gear away and suspend it with wire, if possible. On models CG and CH, the steering gear is lowered with the crossmember. Detach the engine pipe along with the front and rear engine mounting through bolts. Remove the bolts retaining the centre member and withdraw it while someone steadies the engine. Lower the crossmember; manoeuvre across and out from under the vehicle. For CG and CH models, disconnect hydraulic lines from the power steering gear before lowering the crossmember with the steering gear. Putting the installation back on the car is basically the reverse of the removal process. Follow the steps outlined and remember to check the crossmember for damage and renew accordingly. Check stabiliser bar bushes, which are on the bracket and bolts, and tighten correctly. During mounting, don't cause damage of the steering gear boots. For CE models, the steering gear retaining bolts should be torque to situation. For CG and CH Models firstly mount the steering gear properly. Then raise the crossmember and guide the intermediate shaft into the firewall cavity. When the gear is high enough fit and tighten the power steering hoses. Tighten the control arm rear pivot bush bracket bolts then install front pivot bolt loosely. Install stabiliser bar link components in noted order and tighten retaining nut. Attach the center member, tightening the retaining bolts, then take the front wheels back on and lower the vehicle, bouncing the front to stabilise suspension and lightly settling the bushes making sure to then tighten the front control arm pivot bolt, and finally securely connect the battery terminal on models with airbag.