How to remove and install the rear seat cushion and Fuel Sending Unit on Mitsubishi Lancer?

To install or remove the rear seat cushion, find the two retaining clips on the front of the cushion, then pull each clip towards the front of the vehicle and then lift the cushion upwards to remove it. Then, lift the access cover using a flat-bladed screwdriver to prise up the cover and then lift it off the floor. Unplug the wiring of the Fuel Sending Unit, labeling it in relation to the fuel tank so it becomes easier to install later and clean up around the Fuel Sending Unit to avoid dirt getting into the tank. Take out the retaining nuts and then carefully manipulate the Fuel Sending Unit out of the fuel tank and be careful not to drop anything into the tank. To install, seal off the Fuel Sending Unit again to prevent fuel leaks, install the Fuel Sending Unit in the same location as when removing it, screw in the retaining nuts as tight as possible, and make sure the wiring is in place.

Genuine Mitsubishi Fuel Sending Unit

Fuel Sender

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

13 Fuel Sending Units found

View related parts
Mitsubishi Fuel Gauge Sending Unit Part Number: MN139785
$107.35 MSRP: $149.10
You Save: $41.75 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Gauge Unit, Fuel Tank; Fuel Sending Unit; Sending Unit
Fits the following Mitsubishi Models:
- Outlander | 2005-2006 | LS, Limited, SE, XLS | 4 Cyl 2.4 L GAS
View related parts
Mitsubishi Fuel Gauge Sending Unit Part Number: 1718A048
$108.90 MSRP: $151.25
You Save: $42.35 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Gauge Unit, Fuel Tank; Fuel Sending Unit; Sending Unit
Fits the following Mitsubishi Models:
- Eclipse | 2006-2012 | GS, GS Sport, GT, SE, Spyder GS, Spyder GS Sport, Spyder GT, Spyder SE | 4 Cyl 2.4 L GAS, 6 Cyl 3.8 L GAS
- Galant | 2006-2012 | DE, ES, FE, GTS, LS, Ralliart, SE, Sport Edition, Sport V6 | 4 Cyl 2.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Mitsubishi Fuel Gauge Sending Unit Part Number: 1718A036
$111.37 MSRP: $154.68
You Save: $43.31 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Gauge Unit, Fuel Tank; Fuel Sending Unit; Gauge Unit; Fuel Sender Unit
Fits the following Mitsubishi Models:
- Eclipse Cross | 2022-2025, 2018-2020 | Black Edition, ES, LE, Ralliart, SE, SE Special Edition, SEL, SEL Special Edition, SEL Touring, SP | 4 Cyl 1.5 L GAS
- Outlander | 2007-2020 | ES, GT, LE, LS, SE, SEL, SP, XLS | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS
- Outlander Sport | 2011-2025 | BE, ES, GT, GT Special Edition, LE, Ralliart, S, SE, SE Special Edition, SEL, SP, Trail Edition | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View More
View related parts
Mitsubishi Fuel Gauge Sending Unit Part Number: 1718A035
$111.37 MSRP: $154.68
You Save: $43.31 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Gauge Unit, Fuel Tank; Fuel Sending Unit; Gauge Unit; Fuel Sender Unit
Fits the following Mitsubishi Models:
- Eclipse Cross | 2022, 2018-2020 | ES, LE, SE, SE Special Edition, SEL, SEL Special Edition, SP | 4 Cyl 1.5 L GAS
- Outlander | 2007-2020 | ES, GT, LE, LS, SE, SEL, SP, XLS | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS
- Outlander Sport | 2011-2022 | BE, ES, GT, GT Special Edition, LE, S, SE, SE Special Edition, SEL, SP | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View More
View related parts
Mitsubishi Fuel Sender Unit Part Number: 1718A156
$114.08 MSRP: $158.45
You Save: $44.37 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Gauge Unit, Fuel Tank; Fuel Sending Unit
Fits the following Mitsubishi Models:
- Outlander Sport | 2014-2015 | ES, GT, SE | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View related parts
Mitsubishi Fuel Gauge Sending Unit Part Number: MN139857
$149.48 MSRP: $202.55
You Save: $53.07 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Gauge Unit, Fuel Tank; Fuel Sending Unit; Sending Unit
Fits the following Mitsubishi Models:
- Outlander | 2005-2006 | LS, Limited, SE, XLS | 4 Cyl 2.4 L GAS
View related parts
Mitsubishi Fuel Gauge Sending Unit Part Number: MN120152
$237.11 MSRP: $321.28
You Save: $84.17 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Gauge Unit, Fuel Tank; Fuel Sending Unit; Sending Unit
Fits the following Mitsubishi Models:
- Lancer | 2003-2004 | Evolution | 4 Cyl 2.0 L GAS
View related parts
Mitsubishi Fuel Gauge Sending Unit Part Number: MR983976
$54.42 MSRP: $75.58
You Save: $21.16 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Gauge Unit, Fuel Tank; Fuel Sending Unit; Sending Unit
Fits the following Mitsubishi Models:
- Endeavor | 2004-2005 | LS, Limited, XLS | 6 Cyl 3.8 L GAS
View related parts
Mitsubishi Fuel Gauge Sending Unit Part Number: MR959988
$54.42 MSRP: $75.58
You Save: $21.16 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Gauge Unit, Fuel Tank; Fuel Sending Unit; Sending Unit
Fits the following Mitsubishi Models:
- Endeavor | 2004 | LS, Limited, XLS | 6 Cyl 3.8 L GAS
View related parts
Mitsubishi Fuel Gauge Sending Unit Part Number: MB434245
$59.98 MSRP: $83.30
You Save: $23.32 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Gauge Unit, Fuel Tank; Fuel Sending Unit; Sending Unit
Fits the following Mitsubishi Models:
- Van | 1987-1990 | Base, LS | 4 Cyl 2.4 L GAS
View related parts
Mitsubishi Fuel Gauge Sending Unit, Passenger Side Part Number: AX000817
$142.15 MSRP: $192.62
You Save: $50.47 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Gauge Unit, Fuel Tank; Fuel Level Sensor; Fuel Sending Unit; Gauge Unit
- Position: Passenger Side
Fits the following Mitsubishi Models:
- Outlander | 2022-2025 | Black Edition, ES, SE, SE Launch Edition, SEL, SEL Launch Edition | 4 Cyl 2.5 L GAS
View related parts
Mitsubishi Fuel Gauge Sending Unit Part Number: AX000816
$142.15 MSRP: $192.62
You Save: $50.47 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Gauge Unit, Fuel Tank; Fuel Level Sensor; Fuel Sending Unit; Gauge Unit
Fits the following Mitsubishi Models:
- Outlander | 2022-2025 | Black Edition, ES, SE, SE Launch Edition, SEL, SEL Launch Edition | 4 Cyl 2.5 L GAS
View related parts
Mitsubishi Fuel Gauge Sending Unit, Driver Side Part Number: AX000815
$191.08 MSRP: $258.92
You Save: $67.84 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Gauge Unit, Fuel Tank; Fuel Level Sensor; Fuel Sending Unit; Gauge Unit
- Position: Driver Side
Fits the following Mitsubishi Models:
- Outlander | 2022-2025 | Black Edition, ES, SE, SE Launch Edition, SEL, SEL Launch Edition | 4 Cyl 2.5 L GAS

Mitsubishi Fuel Sending Unit

The Mitsubishi Fuel Sending Unit provides a real time display of the quantity of gasoline remaining so the gauge and warning light can speak with accuracy. The trip is guaranteed to be worry free. In the broader Mitsubishi range, a tradition of intelligent innovation underpins this uncomplicated but critical component. Whether it is spirited MIVEC engines or Super All Wheel Control that clings to slippery roads, each model in the range combines intelligent power with user friendly technology such as cruise control and smartphone connection that keep the journey easy and connected. Every driver of a Mitsubishi has confidence. The long history of the brand, beginning with its first Model A sedan through advances in plug in hybrids, demonstrates that efficiency, safety, and easy operation are paramount. The same spirit pervades all the parts that are selected to be reliable. The Fuel Sending Unit is mounted inside the tank and is based on a floating arm mounted on a pivoting arm that slides over a variable resistor. This resistor varies the electrical resistance as the fuel rises or falls. This adjustment is relayed immediately to the dashboard needle, informing the driver of the precise level. When the float goes down to a predetermined low level, a different circuit causes the reserve lamp to light so that refueling is never a surprise. This feedback is maintained by a smooth float motion and clean electrical contact to ensure that a worn unit will result in a stuck or wandering gauge. It is time to replace the Fuel Sending Unit before it causes inconvenience by giving misreadings.

Pick genuine OEM Fuel Sending Unit if you want superb performance and durability that lasts. Mitsubishi builds that using high-grade materials and official factory techniques to meet very strict standards. This means you get parts you can actually trust for your daily drive. Finding the right parts is simple in the massive stock of genuine inventory. You can stop guessing if a part will fit or hold up. You will love the low prices, dependable service and the real manufacturer's warranty on Mitsubishi Fuel Sending Unit. Order today and the store will ship your brand-new items to your door as fast as possible.

Mitsubishi Fuel Sending Unit Parts Questions & Experts Answers

Fuel Gauge Sending Unit
MN120152
Q: How to remove and install the rear seat cushion and Fuel Sending Unit on Mitsubishi Lancer?
A:
To install or remove the rear seat cushion, find the two retaining clips on the front of the cushion, then pull each clip towards the front of the vehicle and then lift the cushion upwards to remove it. Then, lift the access cover using a flat-bladed screwdriver to prise up the cover and then lift it off the floor. Unplug the wiring of the Fuel Sending Unit, labeling it in relation to the fuel tank so it becomes easier to install later and clean up around the Fuel Sending Unit to avoid dirt getting into the tank. Take out the retaining nuts and then carefully manipulate the Fuel Sending Unit out of the fuel tank and be careful not to drop anything into the tank. To install, seal off the Fuel Sending Unit again to prevent fuel leaks, install the Fuel Sending Unit in the same location as when removing it, screw in the retaining nuts as tight as possible, and make sure the wiring is in place.