How to replace a leaking toe drive axle's Axle Shaft Seal on Mitsubishi Galant?

The locations of the toe Axle Shaft Seals are on the sides of the transaxle. The inner ends of the driveaxles are splined into the differential side gears. In case of suspicion of a Axle Shaft Seal leak, the vehicle should be raised and supported on jackstands. Lubricant will be seen on the side of the transaxle if a seal is leaking. Remove driveaxle to replace the seal. Next, carefully use a screwdriver or prybar to pry the oil seal from the transaxle bore. A special seal removal tool may be used for this task which is available at most auto parts stores. Use of the special oil seal removal tool will be necessary if basic tools don't work. When the old seal has been removed, drive the new oil seal squarely into the bore using a seal installer until fully seated. Reinstall the drive axle finally.

How can the axle shafts be removed without disturbing the differential assembly or the Axle Shaft Seal on Mitsubishi Montero?

The axleshafts can be removed without disturbing the differential assembly, which is important for oil seal replacement and for removing the differential carrier from the rear axle casing. Start by elevating the back end of the vehicle up and support the vehicle with jackstands. The front wheels need to be blocked so the vehicle doesn't roll. Remove the rear wheels and release the parking brake; drain the differential lubricant into a suitable container and finger-tighten the drain plug. With drum brake models, remove the drum and the metal brake line from the wheel cylinder without disassembling the brakes. Detach the vehicle's parking brake cables without removing the cables from the levers in the rear brake assemblies. Only remove the cable on the side of the axle shaft being removed if only one cable is being removed. Detach the four nuts and lock washers that are securing the bearing case and brake backing plate to the axle housing, thus withdrawing the axle, bearing case, brake backing plate, and brake assembly. A slide hammer-type axle puller may be necessary for dislodging the bearing housing. Also, care must be taken to support the axle shaft during removal so that the old seal will not be damaged. Remove the O-ring and the shim(s) at the rear axle housing flange, ensuring to retain the shim(s) for reinstallation. Before putting the new seal with the rubber side facing out, take out the oil seal from the housing and clean up area where the seal fits. The axleshaft assembly should be taken to the dealer service department or an automotive machine shop if the outer oil seal or wheel bearing needs replacement. Before assembling the two components, clear old gasket sealer and rust off the mating surfaces. Then pack the bearing case and axle housing end with high-temperature wheel bearing grease and lubricate the oil seal lip. When reassembling, install the left-side shaft first, then a 0.040 inch shim and the new O-ring on the left end of the axle housing. After applying a thin and even coat of silicone-type gasket sealer to the bearing case mating surface, install the left-side axle/brake assembly, taking care not to damage the oil seal. Tighten the four lock washers and nuts to the required torque. Install the right-side axle without shim or O-ring and lightly tighten the nuts to 5 in-lbs. This will create a gap between the bearing case and axle housing end flange that must be measured with a feeler gauge. Choose a shim whose thickness matches the measured gap and another shim whose thickness is 0.020 to 0.079-inch. After installing the selected shims and new O-ring on the axle housing end, apply silicone gasket sealer to the bearing case mating surface, and install the axle assembly, securing it with lock washers and nuts tightened to spec. Utilize a dial indicator to verify the axial play of the axle shaft. Replace shims as required and recheck until the axial play is within specification limits if it does not meet specifications. After reinstalling the parking brake cables, connect the brake lines and install the brake drums, bleeding the brakes at a rear wheel cylinde When all is done tighten the rear axle housing drain plug to specifications. Then fill the rear axle housing with approved gear lubricant and install and tighten the filler plug. Next, install the wheels and lower the vehicle. Finally, test drive the vehicle and check for leaks at the wheel bearing case attachment.

Genuine Mitsubishi Axle Shaft Seal

CV Axle Seal

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

30 Axle Shaft Seals found

View related parts
Mitsubishi Outer Cover, Passenger Side Part Number: MR145574
$4.93 MSRP: $6.42
You Save: $1.49 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover, Front Axle Shaft DIF; Axle Shaft Seal; Wheel Seal; Dust Cover; Inner Shaft Cover; Outer Seal
- Position: Passenger Side
Fits the following Mitsubishi Models:
- Eclipse | 2000-2012 | GT, GTS, SE, Spyder GT, Spyder GTS | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
- Endeavor | 2010-2011, 2004-2008 | LS, Limited, SE, XLS | 6 Cyl 3.8 L GAS
- Galant | 1999-2009 | ES, GTS, GTZ, LS, Ralliart, Sport V6 | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
- Lancer | 2004-2006 | Ralliart, Sportback, Sportback Ralliart | 4 Cyl 2.4 L GAS
- Outlander | 2003-2006 | LS, Limited, SE, XLS | 4 Cyl 2.4 L GAS
View More
View related parts
Mitsubishi Inner Cover, Passenger Side Part Number: MB526617
$5.09 MSRP: $6.63
You Save: $1.54 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover, Front Axle Shaft DUS; Axle Shaft Seal; Wheel Seal; Dust Cover; Inner Shaft Dust Shield; Inner Shaft Cover; Inner Seal
- Position: Passenger Side
Fits the following Mitsubishi Models:
- Diamante | 1997 | ES, LS | 6 Cyl 3.5 L GAS
- Eclipse | 2000-2011 | GT, GTS, SE, Spyder GT, Spyder GTS | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
- Endeavor | 2010-2011, 2004-2008 | LS, Limited, SE, XLS | 6 Cyl 3.8 L GAS
- Galant | 1999-2009 | ES, GTS, GTZ, LS, Ralliart, Sport V6 | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
- Lancer | 2004-2006 | Ralliart, Sportback, Sportback Ralliart | 4 Cyl 2.4 L GAS
- Outlander | 2003-2006 | LS, Limited, SE, XLS | 4 Cyl 2.4 L GAS
View More
View related parts
Mitsubishi Outer Seal, Passenger Side Part Number: 3816A004
$7.77 MSRP: $10.12
You Save: $2.35 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover, Front Axle Shaft DIF; Axle Shaft Seal; Wheel Seal
- Position: Passenger Side
Fits the following Mitsubishi Models:
- Eclipse | 2006-2012 | GT, SE, Spyder GT | 6 Cyl 3.8 L GAS
View related parts
Mitsubishi Inner Shaft Cover Part Number: MB160948
$8.58 MSRP: $11.17
You Save: $2.59 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover, Front Axle Shaft DUS; Axle Shaft Seal; Wheel Seal; Bearing Seal; Axle Seals; Inner Seal
Fits the following Mitsubishi Models:
- Mighty Max | 1992-1996 | 1 Ton, Base | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS
- Montero | 1992-2006 | Base, LS, Limited, RS, SR, XLS | 6 Cyl 3.0 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS
- Montero Sport | 1997-2004 | ES, LS, Limited, XLS, XS | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.5 L GAS
View More
View related parts
Mitsubishi Axle Seals Part Number: MB837719
$8.68 MSRP: $11.30
You Save: $2.62 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Oil Seal, Rear Axle Shaft; Axle Shaft Seal; Wheel Seal; Bearing Oil Seal; Bearing Seal; Seal
Fits the following Mitsubishi Models:
- Mighty Max | 1984-1996 | 1 Ton, Base, S, SP, SPX, Sport | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L DIESEL, 4 Cyl 2.4 L GAS, 4 Cyl 2.6 L GAS, 6 Cyl 3.0 L GAS
- Montero | 1984-2004 | Base, LS, Limited, RS, SP, SR, Sport, XLS | 4 Cyl 2.6 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS
- Montero Sport | 1997-2004 | ES, LS, Limited, XLS, XS | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.5 L GAS
View More
View related parts
Mitsubishi Axle Seals Part Number: MB664612
$9.55 MSRP: $12.43
You Save: $2.88 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Oil Seal, Rear Axle Shaft; Axle Shaft Seal; Wheel Seal; Bearing Oil Seal; Bearing Seal
Fits the following Mitsubishi Models:
- Mighty Max | 1995-1996 | Base | 4 Cyl 2.4 L GAS
- Montero | 1992-2002 | Base, LS, Limited, RS, SR, XLS | 6 Cyl 3.0 L GAS, 6 Cyl 3.5 L GAS
- Montero Sport | 1997-2004 | ES, LS, Limited, XLS, XS | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.5 L GAS
View More
View related parts
Mitsubishi Axle Seals, Driver Side Part Number: 3515A049
$10.55 MSRP: $13.73
You Save: $3.18 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Oil Seal, Rear Differential Side B; Axle Shaft Seal; Axle Seal
- Position: Driver Side
Fits the following Mitsubishi Models:
- Lancer | 2010-2015, 2008 | Evolution Final Edition, Evolution GSR, Evolution MR, Evolution MR Touring, Evolution SE | 4 Cyl 2.0 L GAS
View related parts
Mitsubishi Dust Seal Part Number: MB160946
$12.81 MSRP: $16.68
You Save: $3.87 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Dust Seal, Front Axle Housi; Drive Axle Shaft Seal; Axle Shaft Seal; Wheel Seal; Axle Tube Seal; Axle Seals; Outer Seal; Seal
Fits the following Mitsubishi Models:
- Mighty Max | 1987-1995 | 1 Ton, Base, SPX, Sport | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS, 4 Cyl 2.6 L GAS, 6 Cyl 3.0 L GAS
- Montero | 1992-2006 | Base, LS, Limited, RS, SR, XLS | 6 Cyl 3.0 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS
- Montero Sport | 1997-2004 | ES, LS, Limited, XLS, XS | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.5 L GAS
View More
View related parts
Mitsubishi Axle Seals Part Number: MB092437
$12.95 MSRP: $16.87
You Save: $3.92 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Oil Seal, Rear Axle Shaft; Axle Shaft Seal; Wheel Seal; Oil Seal; Bearing Oil Seal; Wheel Bearing Oil Seal; Bearing Seal; Seal
Fits the following Mitsubishi Models:
- Mighty Max | 1984-1996 | 1 Ton, Base, S, SP, SPX, Sport | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L DIESEL, 4 Cyl 2.4 L GAS, 4 Cyl 2.6 L GAS, 6 Cyl 3.0 L GAS
- Montero | 1984-1991 | Base, LS, RS, SP, Sport | 4 Cyl 2.6 L GAS, 6 Cyl 3.0 L GAS
- Montero Sport | 1997-2004 | ES, LS, Limited, XLS, XS | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.5 L GAS
View More
View related parts
Mitsubishi Side Seals Part Number: MB393883
$13.54 MSRP: $17.63
You Save: $4.09 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Oil Seal, Front Differential Side; Axle Shaft Seal; Wheel Seal; Oil Seal; Axle Seals; Outer Seal
Fits the following Mitsubishi Models:
- Mighty Max | 1990-1994 | 1 Ton, Base | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS
- Montero | 1989-2006 | Base, LS, Limited, RS, SP, SR, Sport, XLS | 6 Cyl 3.0 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS
- Montero Sport | 1997-2004 | ES, LS, Limited, XLS, XS | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.5 L GAS
View More
View related parts
Mitsubishi Axle Seals Part Number: MB290013
$14.28 MSRP: $18.60
You Save: $4.32 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Oil Seal, Front Differential Side; Axle Differential Seal; Differential Axle Seal; Axle Shaft Seal; Wheel Seal; Outer Seal; Side Seals
Fits the following Mitsubishi Models:
- Mighty Max | 1984-1989 | 1 Ton, Base, S, SP, SPX, Sport | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L DIESEL, 4 Cyl 2.6 L GAS
- Montero | 1992-1995, 1984-1989 | Base, LS, RS, SP, SR, Sport | 4 Cyl 2.6 L GAS, 6 Cyl 3.0 L GAS
- Van | 1987-1989 | Base, LS | 4 Cyl 2.4 L GAS
View More
View related parts
Mitsubishi Pinion Seal Part Number: MB393929
$15.77 MSRP: $20.54
You Save: $4.77 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Oil Seal, Rear Differential; Automatic Transmission Seal; Differential Seal; Axle Shaft Seal; Oil Seal; Front Seal
Fits the following Mitsubishi Models:
- Eclipse | 1990-1999 | Base, GS, GST, GSX, RS, Spyder GS, Spyder GST | 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
- Expo | 1992-1995 | Base, SP | 4 Cyl 2.4 L GAS
- Expo LRV | 1992-1994 | Base, Sport | 4 Cyl 1.8 L GAS, 4 Cyl 2.4 L GAS
- Galant | 1990-1992 | Base, GS, GSR, GSX, LS, VR-4 | 4 Cyl 2.0 L GAS
- Lancer | 2008-2017, 2003-2006 | DE, ES, ES Sportback, Evolution, Evolution Final Edition, Evolution GSR, Evolution MR, Evolution MR Touring, Evolution RS, Evolution SE, GTS, LS, OZ Rally, Ralliart, Ralliart Sportback, SE, Sportback, Sportback Ralliart | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
- Outlander | 2003-2006 | LS, Limited, SE, XLS | 4 Cyl 2.4 L GAS
View More
View related parts
Mitsubishi Axle Seals Part Number: MD707184
$16.67 MSRP: $21.70
You Save: $5.03 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Oil Seal, Differential Case; Differential Seal; Axle Shaft Seal; Oil Seal; Side Seals
Fits the following Mitsubishi Models:
- 3000GT | 1991-1992 | Base, SL, VR-4 | 6 Cyl 3.0 L GAS
- Diamante | 1992 | ES, LS | 6 Cyl 3.0 L GAS
- Eclipse | 1991-1999 | Base, GS, GST, GSX, RS, Spyder GS, Spyder GST | 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
- Eclipse Cross | 2022-2024, 2018-2020 | ES, LE, SE, SE Special Edition, SEL, SEL Special Edition, SEL Touring, SP | 4 Cyl 1.5 L GAS
- Expo | 1992-1995 | Base, SP | 4 Cyl 2.4 L GAS
- Expo LRV | 1992-1994 | Base, Sport | 4 Cyl 1.8 L GAS, 4 Cyl 2.4 L GAS
- Galant | 1994-1998, 1990-1992 | Base, DE, ES, GS, GSR, GSX, LS, S, VR-4 | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
- Lancer | 2009-2017, 2003-2006 | ES, ES Sportback, Evolution, Evolution MR, Evolution RS, Evolution SE, GT, GT Sportback, GTS, GTS Sportback, LS, OZ Rally, Ralliart, Ralliart Sportback, SE, SEL, Sportback, Sportback Ralliart | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
- Outlander | 2003-2020 | ES, GT, LE, LS, Limited, SE, SEL, SP, XLS | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS
- Outlander Sport | 2011-2024 | BE, ES, GT, GT Special Edition, LE, Ralliart, S, SE, SE Special Edition, SEL, SP, Trail Edition | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View More
View related parts
Mitsubishi Axle Seals, Front Part Number: MD755526
$18.66 MSRP: $24.29
You Save: $5.63 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Oil Seal, Transmission Front Differential CA; Axle Shaft Seal; Wheel Seal; Seal
- Position: Front
Fits the following Mitsubishi Models:
- Diamante | 1997-2002 | Base, ES, LS, VR-X | 6 Cyl 3.5 L GAS
- Eclipse | 2000-2005 | GS, GT, GTS, RS, Spyder GS, Spyder GT, Spyder GTS | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS
- Lancer | 2010-2015, 2008 | Evolution Final Edition, Evolution GSR, Evolution MR, Evolution MR Touring, Evolution SE | 4 Cyl 2.0 L GAS
- Outlander PHEV | 2018-2022 | GT, LE, SEL | 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 4 Cyl 2.4 L PLUG-IN HYBRID EV-GAS (PHEV)
View More
View related parts
Mitsubishi Axle Seals, Passenger Side Part Number: MN132370
$20.30 MSRP: $26.43
You Save: $6.13 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Oil Seal, Transmission Case, Other; Axle Shaft Seal; Wheel Seal; Oil Seal; Axle Seal
- Position: Passenger Side
Fits the following Mitsubishi Models:
- Diamante | 2002 | ES, LS, VR-X | 6 Cyl 3.5 L GAS
- Eclipse | 2000-2005 | GS, GT, GTS, RS, Spyder GS, Spyder GT, Spyder GTS | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS
- Lancer | 2010-2015, 2008 | Evolution GSR, Evolution MR, Evolution MR Touring, Evolution SE | 4 Cyl 2.0 L GAS
View More
View related parts
Mitsubishi Bearing Seal Part Number: MB290428
$4.39 MSRP: $5.72
You Save: $1.33 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover, Rear Axle Shaft, Inner; Axle Shaft Seal; Wheel Seal; Dust Shield; Inner Cover; Inner Seal; Outer Seal
Fits the following Mitsubishi Models:
- 3000GT | 1991-1999 | Base, SL, Spyder SL, Spyder VR-4, VR-4 | 6 Cyl 3.0 L GAS
- Eclipse | 1990-1994 | Base, GS, GST, GSX | 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS
View related parts
Mitsubishi Outer Seal Part Number: MB393803
$6.92 MSRP: $9.02
You Save: $2.10 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover, Rear Axle Shaft, Outer; Axle Shaft Seal; Wheel Seal; Axle Seals; Bearing Seal; Outer Cover
Fits the following Mitsubishi Models:
- 3000GT | 1991-1999 | Base, SL, Spyder SL, Spyder VR-4, VR-4 | 6 Cyl 3.0 L GAS
- Eclipse | 1990-1994 | Base, GS, GST, GSX | 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS
- Galant | 1991-1992 | Base, GS, GSR, GSX, LS, VR-4 | 4 Cyl 2.0 L GAS
View More
View related parts
Mitsubishi Axle Seals, Front Part Number: MD742053
$9.01 MSRP: $11.73
You Save: $2.72 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Oil Seal, Transmission Front Differential CA; Axle Shaft Seal; Oil Seal
- Position: Front
Fits the following Mitsubishi Models:
- 3000GT | 1993-1999 | Base, SL, Spyder SL, Spyder VR-4, VR-4 | 6 Cyl 3.0 L GAS
- Diamante | 1993-1996 | ES, LS | 6 Cyl 3.0 L GAS
- Eclipse | 1993-1999 | GS, GST, GSX, Spyder GST | 4 Cyl 2.0 L GAS
View More
View related parts
Mitsubishi Axle Seals, Front Part Number: MN130498
$10.11 MSRP: $13.17
You Save: $3.06 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Oil Seal, Transmission Front Differential CA; Axle Shaft Seal; Oil Seal
- Position: Front
Fits the following Mitsubishi Models:
- Eclipse | 2004-2005 | GS, GT, GTS, RS, Spyder GS, Spyder GT, Spyder GTS | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mitsubishi Axle Seals, Front Part Number: MN130496
$10.11 MSRP: $13.17
You Save: $3.06 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Oil Seal, Transmission Front Differential CA; Axle Shaft Seal; Wheel Seal; Oil Seal
- Position: Front
Fits the following Mitsubishi Models:
- Diamante | 2003-2004 | ES, LS, VR-X | 6 Cyl 3.5 L GAS
- Eclipse | 2004-2005 | GS, GT, GTS, RS, Spyder GS, Spyder GT, Spyder GTS | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS

| Page 1 of 2 |Next >

1-20 of 30 Results

Mitsubishi Axle Shaft Seal

Mitsubishi Axle Shaft Seal keeps crucial lubricant within the drive train, preventing leaks that increase heat and wear as the wheels turn at all speeds to provide smooth power delivery. Ever since beginning as a shipping company which produced the first series production car in Japan, Mitsubishi has pursued pragmatic innovation, the addition of MIVEC engines to provide a spirited reactivity, Super All Wheel Control to ensure stable grip, and plug-in hybrid technology to conserve fuel without sacrificing fun. Cruise control, smartphone connectivity, and expanding collections of smart sensors also mean that every voyage is easier and safer, evidence that Mitsubishi continues to incorporate reliability with user friendly concepts in sedans, crossovers, and rugged utility models. In line with that broad vision, the Axle Shaft Seal can be installed in both front or rear drive setups and it seals the gap between the constant velocity axle and the transmission or differential to ensure that the oil does not leak out even during sharp turns or temperature changes. A small size allows the Axle Shaft Seal to fit into lightweight casings, but its highly durable lip material maintains pressure, prevents grit, and reduces vibration. It reduces friction by maintaining a uniform film of oil on gears and bearings, minimizes noise, and prolongs component life, providing the entire lineup with a uniformly healthy driveshaft. Scheduling visual inspections of residue around the Axle Shaft Seal aid the owners in taking actions before the fluid drops, ensuring normal performance in everyday usage and providing extended assurance on all types of roads.

Pick genuine OEM Axle Shaft Seal if you want superb performance and durability that lasts. Mitsubishi builds that using high-grade materials and official factory techniques to meet very strict standards. This means you get parts you can actually trust for your daily drive. Finding the right parts is simple in the massive stock of genuine inventory. You can stop guessing if a part will fit or hold up. You will love the low prices, dependable service and the real manufacturer's warranty on Mitsubishi Axle Shaft Seal. Order today and the store will ship your brand-new items to your door as fast as possible.

Mitsubishi Axle Shaft Seal Parts Questions & Experts Answers

Inner Cover, Passenger Side
MB526617
Q: How to replace a leaking toe drive axle's Axle Shaft Seal on Mitsubishi Galant?
A:
The locations of the toe Axle Shaft Seals are on the sides of the transaxle. The inner ends of the driveaxles are splined into the differential side gears. In case of suspicion of a Axle Shaft Seal leak, the vehicle should be raised and supported on jackstands. Lubricant will be seen on the side of the transaxle if a seal is leaking. Remove driveaxle to replace the seal. Next, carefully use a screwdriver or prybar to pry the oil seal from the transaxle bore. A special seal removal tool may be used for this task which is available at most auto parts stores. Use of the special oil seal removal tool will be necessary if basic tools don't work. When the old seal has been removed, drive the new oil seal squarely into the bore using a seal installer until fully seated. Reinstall the drive axle finally.
Axle Seals
MB092437
Q: How can the axle shafts be removed without disturbing the differential assembly or the Axle Shaft Seal on Mitsubishi Montero?
A:
The axleshafts can be removed without disturbing the differential assembly, which is important for oil seal replacement and for removing the differential carrier from the rear axle casing. Start by elevating the back end of the vehicle up and support the vehicle with jackstands. The front wheels need to be blocked so the vehicle doesn't roll. Remove the rear wheels and release the parking brake; drain the differential lubricant into a suitable container and finger-tighten the drain plug. With drum brake models, remove the drum and the metal brake line from the wheel cylinder without disassembling the brakes. Detach the vehicle's parking brake cables without removing the cables from the levers in the rear brake assemblies. Only remove the cable on the side of the axle shaft being removed if only one cable is being removed. Detach the four nuts and lock washers that are securing the bearing case and brake backing plate to the axle housing, thus withdrawing the axle, bearing case, brake backing plate, and brake assembly. A slide hammer-type axle puller may be necessary for dislodging the bearing housing. Also, care must be taken to support the axle shaft during removal so that the old seal will not be damaged. Remove the O-ring and the shim(s) at the rear axle housing flange, ensuring to retain the shim(s) for reinstallation. Before putting the new seal with the rubber side facing out, take out the oil seal from the housing and clean up area where the seal fits. The axleshaft assembly should be taken to the dealer service department or an automotive machine shop if the outer oil seal or wheel bearing needs replacement. Before assembling the two components, clear old gasket sealer and rust off the mating surfaces. Then pack the bearing case and axle housing end with high-temperature wheel bearing grease and lubricate the oil seal lip. When reassembling, install the left-side shaft first, then a 0.040 inch shim and the new O-ring on the left end of the axle housing. After applying a thin and even coat of silicone-type gasket sealer to the bearing case mating surface, install the left-side axle/brake assembly, taking care not to damage the oil seal. Tighten the four lock washers and nuts to the required torque. Install the right-side axle without shim or O-ring and lightly tighten the nuts to 5 in-lbs. This will create a gap between the bearing case and axle housing end flange that must be measured with a feeler gauge. Choose a shim whose thickness matches the measured gap and another shim whose thickness is 0.020 to 0.079-inch. After installing the selected shims and new O-ring on the axle housing end, apply silicone gasket sealer to the bearing case mating surface, and install the axle assembly, securing it with lock washers and nuts tightened to spec. Utilize a dial indicator to verify the axial play of the axle shaft. Replace shims as required and recheck until the axial play is within specification limits if it does not meet specifications. After reinstalling the parking brake cables, connect the brake lines and install the brake drums, bleeding the brakes at a rear wheel cylinde When all is done tighten the rear axle housing drain plug to specifications. Then fill the rear axle housing with approved gear lubricant and install and tighten the filler plug. Next, install the wheels and lower the vehicle. Finally, test drive the vehicle and check for leaks at the wheel bearing case attachment.