How to check and renew front brake pads (Brake Caliper, Brake Pads and Brake Rotor) on Mitsubishi Lancer?

To check and renew brake pads, raise the front of the car and support it securely on jackstands. Remove the front wheels. Check the thickness of the brake pad lining using the inspection hole in the caliper body. If any pad is below specification minimum or contaminated, renew the pads in complete set and rectify contamination prior to installation. To prevent the master cylinder reservoir from overflowing when pushing back the caliper pistons, drain about two-thirds of the brake fluid. Carry out this job on one caliper at a time and renew the brake pads in sets of four. Take out the lower caliper guide pin and turn caliper upwards to expose the pads, shims and anti rattle clips. Remove disc pads noting the position of the wear indicators and anti squeal shims. If the guide pins feel tight or wear is uneven, clean and lubricate them for free movement. Insert hammer handle and push the piston back into the caliper. If there are leaks or any deterioration, consider having the caliper overhauled. Each inner pad must be fitted with a pad wear indicator, the anti-squeal shims cleaned and the anti-rattle clips properly seated before placing the pads on the anchor plate. Drop the caliper, put the lower guide pin in place and pump the brake pedal so that the pads fit alongside the Brake Rotor. If needed, top up with fluid, replace front wheels, lower vehicle, and road-test to check operation of brakes. To overhaul the caliper, lift the front of the vehicle, detach the banjo bolt and brake hose, and discard the washers. Take out the guide pins and remove the caliper. The dust boot can then be removed followed by forcing the piston from the caliper bore using compressed air or by pushing the brake pedal. Take off the piston seal. Clean all parts. Check for wear. Apply clean brake fluid to the piston and seal. Then fit the new seal and piston. Reattach the caliper, applying a correct torque on the guide pins and brake hose with sealing washers. You need Bleed the hydraulic system, install the wheel, lower the vehicle. To check the Brake Rotor, lift the front of the vehicle, then remove the wheel, and caliper with pads. The disc must be checked for scores, cracks, and wear. If scored, it must be machined. Examine the runout utilizing a dial gauge and, where required, modify the position of the disc or replace it. Take readings of the disc thickness at eight points, and renew if below specifications. Lift the vehicle and remove the wheel, caliper, and pads before removing and installing the anchor plate. Make a mark on the disc after removing it so you can put it back. Never use a hammer. During installation, be sure the mating faces are clean, torque the anchor plate bolts and refit the brake pads/caliper.

Genuine Mitsubishi Brake Caliper

Caliper

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

48 Brake Calipers found

View related parts
Mitsubishi Caliper, Driver Side Part Number: MR955063
$266.36 MSRP: $376.22
You Save: $109.86 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Kit, Front Brake, Left-Hand; Wheel Cylinder Repair Kit; Brake Caliper
- Position: Driver Side
Fits the following Mitsubishi Models:
- Lancer | 2004-2006 | Ralliart, Sportback, Sportback Ralliart | 4 Cyl 2.4 L GAS
- Outlander | 2003-2004 | LS, XLS | 4 Cyl 2.4 L GAS
View related parts
Mitsubishi Caliper Assembly, Passenger Side Part Number: MR370776
$274.55 MSRP: $387.79
You Save: $113.24 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Kit, Front Brake, Right-Hand; Wheel Cylinder Repair Kit; Brake Caliper; Caliper
- Position: Passenger Side
Fits the following Mitsubishi Models:
- Lancer | 2009-2015 | Ralliart, Ralliart Sportback, SE | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
- Outlander | 2005-2006 | LS, Limited, SE, XLS | 4 Cyl 2.4 L GAS
- Outlander PHEV | 2018-2022 | GT, LE, SEL | 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 4 Cyl 2.4 L PLUG-IN HYBRID EV-GAS (PHEV)
View More
View related parts
Mitsubishi Caliper, Passenger Side Part Number: MN116288
$287.78 MSRP: $406.47
You Save: $118.69 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Kit, Rear Brake, Right-Hand; Wheel Cylinder Repair Kit; Brake Caliper
- Position: Passenger Side
Fits the following Mitsubishi Models:
- Endeavor | 2010-2011, 2004-2008 | LS, Limited, SE, XLS | 6 Cyl 3.8 L GAS
View related parts
Mitsubishi Caliper Assembly, Driver Side Part Number: MR370775
$302.52 MSRP: $427.28
You Save: $124.76 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Kit, Front Brake, Left-Hand; Wheel Cylinder Repair Kit; Brake Caliper; Caliper
- Position: Driver Side
Fits the following Mitsubishi Models:
- Lancer | 2009-2015 | Ralliart, Ralliart Sportback, SE | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
- Outlander | 2005-2006 | LS, Limited, SE, XLS | 4 Cyl 2.4 L GAS
- Outlander PHEV | 2018-2022 | GT, LE, SEL | 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 4 Cyl 2.4 L PLUG-IN HYBRID EV-GAS (PHEV)
View More
View related parts
Mitsubishi Caliper, Driver Side Part Number: MN116287
$306.47 MSRP: $432.87
You Save: $126.40 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Kit, Rear Brake, Left-Hand; Wheel Cylinder Repair Kit; Brake Caliper
- Position: Driver Side
Fits the following Mitsubishi Models:
- Endeavor | 2010-2011, 2004-2008 | LS, Limited, SE, XLS | 6 Cyl 3.8 L GAS
View related parts
Mitsubishi Caliper Assembly, Driver Side Part Number: MR955065
$309.69 MSRP: $437.42
You Save: $127.73 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Kit, Rear Brake, Left-Hand; Wheel Cylinder Repair Kit; Brake Caliper; Caliper
- Position: Driver Side
Fits the following Mitsubishi Models:
- Lancer | 2004-2006 | Ralliart, Sportback, Sportback Ralliart | 4 Cyl 2.4 L GAS
- Outlander | 2005-2006 | LS, Limited, SE, XLS | 4 Cyl 2.4 L GAS
View related parts
Mitsubishi Caliper, Passenger Side Part Number: MR510542
$313.60 MSRP: $442.93
You Save: $129.33 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Kit, Rear Brake, Right-Hand; Wheel Cylinder Repair Kit; Brake Caliper
- Position: Passenger Side
Fits the following Mitsubishi Models:
- Montero | 2001-2006 | Limited, XLS | 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS
View related parts
Mitsubishi Caliper, Driver Side Part Number: MR510541
$313.60 MSRP: $442.93
You Save: $129.33 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Kit, Rear Brake, Left-Hand; Wheel Cylinder Repair Kit; Brake Caliper
- Position: Driver Side
Fits the following Mitsubishi Models:
- Montero | 2001-2006 | Limited, XLS | 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS
View related parts
Mitsubishi Caliper, Driver Side Part Number: MR407676
$344.70 MSRP: $486.87
You Save: $142.17 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Kit, Front Brake, Left-Hand; Wheel Cylinder Repair Kit; Brake Caliper
- Position: Driver Side
Fits the following Mitsubishi Models:
- Montero | 2001-2006 | Limited, XLS | 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS
View related parts
Mitsubishi Caliper, Passenger Side Part Number: MR407675
$344.84 MSRP: $487.07
You Save: $142.23 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Kit, Front Brake, Right-Hand; Wheel Cylinder Repair Kit; Brake Caliper
- Position: Passenger Side
Fits the following Mitsubishi Models:
- Montero | 2001-2006 | Limited, XLS | 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS
View related parts
Mitsubishi Caliper Assembly, Driver Side Part Number: 4605A263
$348.17 MSRP: $491.77
You Save: $143.60 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Kit, Rear Brake, Left-Hand; Wheel Cylinder Repair Kit; Brake Caliper; Caliper
- Position: Driver Side
Fits the following Mitsubishi Models:
- Lancer | 2008-2015 | GT, GT Sportback, GTS, GTS Sportback, Ralliart, Ralliart Sportback | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
- Outlander | 2008-2013 | ES, SE | 4 Cyl 2.4 L GAS
- Outlander Sport | 2011-2012 | ES, SE | 4 Cyl 2.0 L GAS
View More
View related parts
Mitsubishi Caliper, Passenger Side Part Number: 4605A478
$356.74 MSRP: $503.87
You Save: $147.13 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Kit, Rear Brake, Right-Hand; Wheel Cylinder Repair Kit; Brake Caliper
- Position: Passenger Side
Fits the following Mitsubishi Models:
- Lancer | 2008-2017 | DE, ES, ES Sportback, GT, GT Sportback, GTS, GTS Sportback, Ralliart, Ralliart Sportback, SE, SEL | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View related parts
Mitsubishi Caliper Assembly, Passenger Side Part Number: 4605A264
$365.94 MSRP: $516.86
You Save: $150.92 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Kit, Rear Brake, Right-Hand; Wheel Cylinder Repair Kit; Brake Caliper; Caliper
- Position: Passenger Side
Fits the following Mitsubishi Models:
- Lancer | 2008-2015 | GT, GT Sportback, GTS, GTS Sportback, Ralliart, Ralliart Sportback | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
- Outlander | 2008-2013 | ES, SE | 4 Cyl 2.4 L GAS
- Outlander Sport | 2011-2012 | ES, SE | 4 Cyl 2.0 L GAS
View More
View related parts
Mitsubishi Caliper, Driver Side Part Number: 4605A477
$371.26 MSRP: $524.38
You Save: $153.12 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Kit, Rear Brake, Left-Hand; Wheel Cylinder Repair Kit; Brake Caliper
- Position: Driver Side
Fits the following Mitsubishi Models:
- Lancer | 2008-2017 | DE, ES, ES Sportback, GT, GT Sportback, GTS, GTS Sportback, Ralliart, Ralliart Sportback, SE, SEL | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View related parts
Mitsubishi Caliper Assembly, Driver Side Part Number: 4605B001
$435.53 MSRP: $615.15
You Save: $179.62 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Kit, Front Brake, Left-Hand; Wheel Cylinder Repair Kit; Brake Caliper; Caliper
- Position: Driver Side
Fits the following Mitsubishi Models:
- Mirage | 2014-2015 | DE, ES, RF | 3 Cyl 1.2 L GAS
View related parts
Mitsubishi Caliper Assembly, Passenger Side Part Number: 4605B002
$438.55 MSRP: $619.42
You Save: $180.87 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Kit, Front Brake, Right-Hand; Wheel Cylinder Repair Kit; Brake Caliper; Caliper
- Position: Passenger Side
Fits the following Mitsubishi Models:
- Mirage | 2014-2015 | DE, ES, RF | 3 Cyl 1.2 L GAS
View related parts
Mitsubishi Caliper, Passenger Side Part Number: 4605B478
$446.90 MSRP: $631.22
You Save: $184.32 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Kit, Front Brake, Right-Hand; Wheel Cylinder Repair Kit; Brake Caliper
- Position: Passenger Side
Fits the following Mitsubishi Models:
- Eclipse Cross | 2022-2025, 2018-2020 | Black Edition, ES, LE, Ralliart, SE, SE Special Edition, SEL, SEL Special Edition, SEL Touring, SP | 4 Cyl 1.5 L GAS
View related parts
Mitsubishi Caliper, Driver Side Part Number: 4605B477
$446.90 MSRP: $631.22
You Save: $184.32 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Kit, Front Brake, Left-Hand; Wheel Cylinder Repair Kit; Brake Caliper
- Position: Driver Side
Fits the following Mitsubishi Models:
- Eclipse Cross | 2022-2025, 2018-2020 | Black Edition, ES, LE, Ralliart, SE, SE Special Edition, SEL, SEL Special Edition, SEL Touring, SP | 4 Cyl 1.5 L GAS
View related parts
Mitsubishi Caliper Assembly, Passenger Side Part Number: 4605B844
$462.12 MSRP: $652.71
You Save: $190.59 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Kit, Rear Brake, Right-Hand; Wheel Cylinder Repair Kit; Brake Caliper; Caliper
- Position: Passenger Side
Fits the following Mitsubishi Models:
- Outlander | 2014-2018 | ES, GT, LE, SE, SEL | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS
- Outlander PHEV | 2018 | GT, SEL | 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV)
- Outlander Sport | 2013-2025 | BE, ES, GT, GT Special Edition, LE, Ralliart, S, SE, SE Special Edition, SEL, SP, Trail Edition | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View More
View related parts
Mitsubishi Caliper Assembly, Driver Side Part Number: 4605B843
$462.12 MSRP: $652.71
You Save: $190.59 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Kit, Rear Brake, Left-Hand; Wheel Cylinder Repair Kit; Brake Caliper; Caliper
- Position: Driver Side
Fits the following Mitsubishi Models:
- Outlander | 2014-2018 | ES, GT, LE, SE, SEL | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS
- Outlander PHEV | 2018 | GT, SEL | 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV)
- Outlander Sport | 2013-2025 | BE, ES, GT, GT Special Edition, LE, Ralliart, S, SE, SE Special Edition, SEL, SP, Trail Edition | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View More

| Page 1 of 3 |Next >

1-20 of 48 Results

Mitsubishi Brake Caliper

The Brake Caliper converts the pressure from the brake pedal into hydraulic pressure. This causes the caliper to squeeze the brake disc rotor, which then slows down the car. Mitsubishi is one of the old automobile manufacturers and has origins that can be traced back to 1870. The Japanese carmaker is known to manufacture vehicles that are durable, fuel-efficient, and offer spirited performance. This is due to the efficiencies built into the car by Mitsubishi's MIVEC variable valve timing system, which helps the vehicle extract maximum mileage from each drop of fuel. The brand bolsters grip on tough or wet roads using Super All Wheel Control, while contemporary cabins make full use of cruise control and easy smartphone link that gives you music and navigation at hand. Mitsubishi has been experimenting with other technologies as well, including plug-in hybrids, fuel cell trials, and lightweight designs, with the continuous goal of delivering cleaner drives and lower running costs. Moreover, they ensure their solution won't complicate maintenance. Whether you are a first-time or seasoned owner, you will appreciate the simple operation and reliable engineering across the lineup. There is a Brake Caliper located beside each disc rotor. When you press your brake pedal, hydraulic fluid pushes one or more pistons inside this heavy cast iron-shaped caliper. This causes two friction pads to squeeze the spinning disc to slow the car down. When you brake, the heat from friction pushes out into the surrounding air. Floating versions glide on pins for even pressure. Meanwhile, fixed types mount solidly and work pistons on both sides. The same mission is shared by each Brake Caliper, which is steady pad compression, even wear, and dependable braking for every Mitsubishi on the road.

Pick genuine OEM Brake Caliper if you want superb performance and durability that lasts. Mitsubishi builds that using high-grade materials and official factory techniques to meet very strict standards. This means you get parts you can actually trust for your daily drive. Finding the right parts is simple in the massive stock of genuine inventory. You can stop guessing if a part will fit or hold up. You will love the low prices, dependable service and the real manufacturer's warranty on Mitsubishi Brake Caliper. Order today and the store will ship your brand-new items to your door as fast as possible.

Mitsubishi Brake Caliper Parts Questions & Experts Answers

Caliper, Passenger Side
4605A436
Q: How to check and renew front brake pads (Brake Caliper, Brake Pads and Brake Rotor) on Mitsubishi Lancer?
A:
To check and renew brake pads, raise the front of the car and support it securely on jackstands. Remove the front wheels. Check the thickness of the brake pad lining using the inspection hole in the caliper body. If any pad is below specification minimum or contaminated, renew the pads in complete set and rectify contamination prior to installation. To prevent the master cylinder reservoir from overflowing when pushing back the caliper pistons, drain about two-thirds of the brake fluid. Carry out this job on one caliper at a time and renew the brake pads in sets of four. Take out the lower caliper guide pin and turn caliper upwards to expose the pads, shims and anti rattle clips. Remove disc pads noting the position of the wear indicators and anti squeal shims. If the guide pins feel tight or wear is uneven, clean and lubricate them for free movement. Insert hammer handle and push the piston back into the caliper. If there are leaks or any deterioration, consider having the caliper overhauled. Each inner pad must be fitted with a pad wear indicator, the anti-squeal shims cleaned and the anti-rattle clips properly seated before placing the pads on the anchor plate. Drop the caliper, put the lower guide pin in place and pump the brake pedal so that the pads fit alongside the Brake Rotor. If needed, top up with fluid, replace front wheels, lower vehicle, and road-test to check operation of brakes. To overhaul the caliper, lift the front of the vehicle, detach the banjo bolt and brake hose, and discard the washers. Take out the guide pins and remove the caliper. The dust boot can then be removed followed by forcing the piston from the caliper bore using compressed air or by pushing the brake pedal. Take off the piston seal. Clean all parts. Check for wear. Apply clean brake fluid to the piston and seal. Then fit the new seal and piston. Reattach the caliper, applying a correct torque on the guide pins and brake hose with sealing washers. You need Bleed the hydraulic system, install the wheel, lower the vehicle. To check the Brake Rotor, lift the front of the vehicle, then remove the wheel, and caliper with pads. The disc must be checked for scores, cracks, and wear. If scored, it must be machined. Examine the runout utilizing a dial gauge and, where required, modify the position of the disc or replace it. Take readings of the disc thickness at eight points, and renew if below specifications. Lift the vehicle and remove the wheel, caliper, and pads before removing and installing the anchor plate. Make a mark on the disc after removing it so you can put it back. Never use a hammer. During installation, be sure the mating faces are clean, torque the anchor plate bolts and refit the brake pads/caliper.