How to remove and install a Wheel Stud and other components with disc and drum brakes on Mitsubishi Mirage?

In order to remove and install components with disc brakes, first raise the proper end of the vehicle and support it safely with jackstands and remove the wheel. Next, remove the brake pads and caliper. Support the caliper aside using a hanger. Detach the outer wheel bearing and lift off the rotor, ensuring the rotor is properly supported with press bars. Drive the stud out with the aid of an arbor press. If you don't have a press, ensure that the rotor is supported evenly and used a blunt drift to carefully drive the old stud out. To install a new stud, clean the stud hole first with a wire brush and start the stud with a hammer and drift pin. Do not use any lubricant or thread sealer. Complete the stud installation using the press or, if no press available, install flat washers and a lug nut to draw the stud into position; hold it fully seated before removing the lug nut and washers. Next, the rotor is installed and the wheel bearings adjusted, followed by the brake caliper and pads. Finally, put the wheel on, remove the jackstands, lower the car, and torque the lug nuts to spec. To access drum brakes, first raise and support the vehicle, then remove its wheel and brake drum. Remove brake shoes if necessary to clear jam. Using a large C-clamp and socket, press out the stud from the axle flange. Coat the serrated part of the stud in liquid soap and press it into the hole. For installing the stud, place flat washers on the stud and thread the lug nut. Then hold the flange while tightening the lug to pull the stud into position. Make sure that the stud is seated all the way before removing the lug nut and washers. If required, fit the brake shoes then the brake drum, then the wheel, and finally remove the jackstands and lower the vehicle and tighten the lug nuts to the proper torque.

Genuine Mitsubishi Wheel Stud

Rim Wheel Stud

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

13 Wheel Studs found

View related parts
Mitsubishi Front Mount Bolt Part Number: MR297292
$2.33 MSRP: $3.03
You Save: $0.70 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bolt, Rear Wheel Hub; Wheel Hub Bolt; Wheel Stud; Wheel Bolt
Fits the following Mitsubishi Models:
- Diamante | 1997-2002 | Base, ES, LS, VR-X | 6 Cyl 3.5 L GAS
- Outlander Sport | 2011-2025 | BE, ES, GT, GT Special Edition, LE, Ralliart, S, SE, SE Special Edition, SEL, SP, Trail Edition | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View related parts
Mitsubishi Hub Mount Bolt Part Number: MU000708
$2.92 MSRP: $3.80
You Save: $0.88 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bolt, Rear Wheel Hub; Wheel Hub Bolt; Wheel Stud; Hub & Bearing Bolt; Axle Nut Mount Bolt; Backing Plate Bolt
- Replaces: MU001822
Fits the following Mitsubishi Models:
- Eclipse Cross | 2022-2025, 2018-2020 | Black Edition, ES, LE, Ralliart, SE, SE Special Edition, SEL, SEL Special Edition, SEL Touring, SP | 4 Cyl 1.5 L GAS
- Lancer | 2008-2017 | DE, ES, ES Sportback, GT, GT Sportback, GTS, GTS Sportback, Ralliart, Ralliart Sportback, SE, SEL | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
- Outlander | 2014-2020 | ES, GT, LE, SE, SEL, SP | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS
- Outlander PHEV | 2018-2022 | GT, LE, SEL | 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 4 Cyl 2.4 L PLUG-IN HYBRID EV-GAS (PHEV)
- Outlander Sport | 2011-2025 | BE, ES, GT, GT Special Edition, LE, Ralliart, S, SE, SE Special Edition, SEL, SP, Trail Edition | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View More
View related parts
Mitsubishi Wheel Bolt Part Number: MB301529
$3.23 MSRP: $4.20
You Save: $0.97 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bolt, Wheel Hub; Wheel Hub Bolt; Wheel Lug Stud; Wheel Stud
Fits the following Mitsubishi Models:
- Montero Sport | 1997-2002 | ES, LS, Limited, XLS, XS | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.5 L GAS
View related parts
Mitsubishi Wheel Stud Part Number: MB911495
$3.30 MSRP: $4.31
You Save: $1.01 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bolt, Wheel Hub, 12X43; Wheel Hub Bolt; Wheel Lug Bolt; Wheel Lug Stud; Wheel Bolt; Hub Assembly Stud; Hub Bolt; Stud
Fits the following Mitsubishi Models:
- 3000GT | 1991-1999 | Base, SL, Spyder SL, Spyder VR-4, VR-4 | 6 Cyl 3.0 L GAS
- Diamante | 1997-2004 | Base, ES, LS, VR-X | 6 Cyl 3.5 L GAS
- Eclipse | 2011-2012, 1990-2009 | Base, GS, GS Sport, GST, GSX, GT, GTS, RS, SE, Spyder GS, Spyder GS Sport, Spyder GST, Spyder GT, Spyder GTS, Spyder SE | 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
- Eclipse Cross | 2022-2025, 2018-2020 | Black Edition, ES, LE, Ralliart, SE, SE Special Edition, SEL, SEL Special Edition, SEL Touring, SP | 4 Cyl 1.5 L GAS
- Endeavor | 2010, 2004-2008 | LS, Limited, SE, XLS | 6 Cyl 3.8 L GAS
- Galant | 2012, 1994-2010, 1985-1987 | Base, DE, ES, FE, GS, GTS, GTZ, LS, Ralliart, S, SE, Sport Edition, Sport V6 | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
- Lancer | 2002-2017 | DE, ES, ES Sportback, Evolution, Evolution GSR, Evolution MR, Evolution MR Touring, Evolution RS, Evolution SE, GT, GT Sportback, GTS, GTS Sportback, LS, OZ Rally, Ralliart, Ralliart Sportback, SE, SEL, Sportback, Sportback Ralliart | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
- Mirage | 2017-2024, 2014-2015, 1993-2002 | BE, Black Edition, Carbonite Edition, DE, ES, GT, LE, LS, RF, S, SE | 3 Cyl 1.2 L GAS, 4 Cyl 1.5 L GAS, 4 Cyl 1.8 L GAS
- Mirage G4 | 2017-2024 | BE, Carbonite Edition, ES, LE, RF, SE | 3 Cyl 1.2 L GAS
- Outlander | 2003-2020 | ES, GT, LE, LS, Limited, SE, SEL, SP, XLS | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS
View More
View related parts
Mitsubishi Wheel Bolt Part Number: MB301509
$3.30 MSRP: $4.30
You Save: $1.00 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bolt, Wheel Hub; Wheel Hub Bolt; Wheel Lug Stud; Wheel Stud
Fits the following Mitsubishi Models:
- Mirage | 2017-2024, 2014-2015 | BE, Black Edition, Carbonite Edition, DE, ES, GT, LE, RF, SE | 3 Cyl 1.2 L GAS
- Mirage G4 | 2017-2024 | BE, Carbonite Edition, ES, LE, RF, SE | 3 Cyl 1.2 L GAS
- Montero Sport | 2003-2004 | ES, LS, Limited, XLS | 6 Cyl 3.0 L GAS, 6 Cyl 3.5 L GAS
View More
View related parts
Mitsubishi Wheel Stud Part Number: MU159002
$4.34 MSRP: $5.65
You Save: $1.31 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bolt, Wheel Hub; Wheel Hub Bolt; Wheel Lug Stud; Wheel Bolt; Hub Bolt
Fits the following Mitsubishi Models:
- Eclipse | 2006-2012 | GS, GS Sport, GT, SE, Spyder GS, Spyder GS Sport, Spyder GT, Spyder SE | 4 Cyl 2.4 L GAS, 6 Cyl 3.8 L GAS
- Endeavor | 2011, 2007 | LS, SE | 6 Cyl 3.8 L GAS
- Galant | 2007-2012 | DE, ES, FE, GTS, Ralliart, SE, Sport Edition, Sport V6 | 4 Cyl 2.4 L GAS, 6 Cyl 3.8 L GAS
View More
View related parts
Mitsubishi Hub & Bearing Bolt Part Number: MU000975
$4.88 MSRP: $6.35
You Save: $1.47 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bolt, Rear Wheel Hub; Wheel Hub Bolt; Wheel Stud
Fits the following Mitsubishi Models:
- Lancer | 2009-2015 | DE, ES, ES Sportback, GT, GT Sportback, GTS, GTS Sportback, Ralliart, Ralliart Sportback, SE | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View related parts
Mitsubishi Wheel Bolt Part Number: 3880A151
$7.33 MSRP: $9.55
You Save: $2.22 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bolt, Rear Wheel Hub, Left-Hand; Wheel Hub Bolt; Wheel Stud
Fits the following Mitsubishi Models:
- Outlander | 2022-2025 | Black Edition, ES, SE, SE Launch Edition, SEL, SEL Launch Edition | 4 Cyl 2.5 L GAS
View related parts
Mitsubishi Wheel Stud Part Number: 3880A150
$7.58 MSRP: $9.87
You Save: $2.29 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bolt, Front Wheel Hub, Left-Hand; Wheel Hub Bolt; Wheel Bolt
Fits the following Mitsubishi Models:
- Outlander | 2022-2025 | Black Edition, ES, SE, SE Launch Edition, SEL, SEL Launch Edition | 4 Cyl 2.5 L GAS
- Outlander PHEV | 2023-2025 | ES, Platinum Edition, Ralliart, SE, SE Tech, SEL, SEL Premium, SEL Touring | 4 Cyl 2.4 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Mitsubishi Hub Assembly Mount Bolt Part Number: AX000179
$3.23 MSRP: $4.20
You Save: $0.97 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bolt, Knuckle; Wheel Hub Bolt; Wheel Stud
Fits the following Mitsubishi Models:
- Outlander | 2022-2025 | Black Edition, ES, SE, SE Launch Edition, SEL, SEL Launch Edition | 4 Cyl 2.5 L GAS
View related parts
Mitsubishi Hub Assembly Mount Bolt Part Number: MUA00177
$4.65 MSRP: $6.05
You Save: $1.40 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bolt, Front Wheel Hub; Wheel Hub Bolt; Wheel Stud
Fits the following Mitsubishi Models:
- Outlander PHEV | 2023-2025 | ES, Platinum Edition, Ralliart, SE, SE Tech, SEL, SEL Premium, SEL Touring | 4 Cyl 2.4 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Mitsubishi Hub Assembly Mount Bolt Part Number: AX000178
$5.48 MSRP: $7.13
You Save: $1.65 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bolt, Rear Wheel Hub; Wheel Hub Bolt; Wheel Stud
- Replaces: 01125A2121
Fits the following Mitsubishi Models:
- Outlander | 2022-2025 | Black Edition, ES, SE, SE Launch Edition, SEL, SEL Launch Edition | 4 Cyl 2.5 L GAS
- Outlander PHEV | 2023-2025 | ES, Platinum Edition, Ralliart, SE, SE Tech, SEL, SEL Premium, SEL Touring | 4 Cyl 2.4 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Mitsubishi Rotor Bolt Part Number: MF240053
$1.72 MSRP: $2.23
You Save: $0.51 (23%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bolt, Washer Assembled, 8; Wheel Hub Bolt; Wheel Stud
Fits the following Mitsubishi Models:
- Eclipse | 1990-1994 | Base, GS, GST | 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS

Mitsubishi Wheel Stud

Mitsubishi Wheel Stud is a fastener that locks each wheel onto the hub and grips firmly so the tires stay planted during every turn and stop. Each product is made of high strength steel, so each Wheel Stud smoothly threads with the included lug nut to form a clamp that can tolerate the application of vehicle weight, road shock, and heat cycling, and does not bend in service or strip its threads. The corrosion resistant finish allows it to remain semi-permanently seated in the hub so that tire changes are easy and repeatable. Whenever one stud becomes weaker, the load shifts to the neighboring stud. Therefore, timely replacement helps to ensure predictable handling and steering, which remains vibration-free across the entire lineup. Thus, a single Wheel Stud can protect the entire suspension system. Mitsubishi, established in 1870, is led by the shipping business but has grown to manufacture Japan's first mass produced car. Then, it had further innovation with MIVEC variable valve timing that provides lively acceleration while also saving fuel. The manufacturer assesses fuel-cell and plug-in hybrid technology. Furthermore, it provides up to classy Super All Wheel Control for added grip on gravel or snow. Moreover, it adds intuitive cruise control plus smartphone link to simplify daily driving. Mitsubishi is also taking its i-MiEV city car through fleet trials. Mitsubishi is seeking to combine smart features with sensible pricing, solid reliability, and user friendly maintenance in sedans, crossovers, and future concepts.

Pick genuine OEM Wheel Stud if you want superb performance and durability that lasts. Mitsubishi builds that using high-grade materials and official factory techniques to meet very strict standards. This means you get parts you can actually trust for your daily drive. Finding the right parts is simple in the massive stock of genuine inventory. You can stop guessing if a part will fit or hold up. You will love the low prices, dependable service and the real manufacturer's warranty on Mitsubishi Wheel Stud. Order today and the store will ship your brand-new items to your door as fast as possible.

Mitsubishi Wheel Stud Parts Questions & Experts Answers

Wheel Stud
MB911495
Q: How to remove and install a Wheel Stud and other components with disc and drum brakes on Mitsubishi Mirage?
A:
In order to remove and install components with disc brakes, first raise the proper end of the vehicle and support it safely with jackstands and remove the wheel. Next, remove the brake pads and caliper. Support the caliper aside using a hanger. Detach the outer wheel bearing and lift off the rotor, ensuring the rotor is properly supported with press bars. Drive the stud out with the aid of an arbor press. If you don't have a press, ensure that the rotor is supported evenly and used a blunt drift to carefully drive the old stud out. To install a new stud, clean the stud hole first with a wire brush and start the stud with a hammer and drift pin. Do not use any lubricant or thread sealer. Complete the stud installation using the press or, if no press available, install flat washers and a lug nut to draw the stud into position; hold it fully seated before removing the lug nut and washers. Next, the rotor is installed and the wheel bearings adjusted, followed by the brake caliper and pads. Finally, put the wheel on, remove the jackstands, lower the car, and torque the lug nuts to spec. To access drum brakes, first raise and support the vehicle, then remove its wheel and brake drum. Remove brake shoes if necessary to clear jam. Using a large C-clamp and socket, press out the stud from the axle flange. Coat the serrated part of the stud in liquid soap and press it into the hole. For installing the stud, place flat washers on the stud and thread the lug nut. Then hold the flange while tightening the lug to pull the stud into position. Make sure that the stud is seated all the way before removing the lug nut and washers. If required, fit the brake shoes then the brake drum, then the wheel, and finally remove the jackstands and lower the vehicle and tighten the lug nuts to the proper torque.