How to adjust and reinstall the throttle stop screw and throttle body on 1.5 litre and 2.4 litre on Mitsubishi Lancer?

On 1.5 litre models, a factory set throttle stop screw is supplied, which is not supplied on other models. Typically, you should not have to make any adjustment to this screw. If it has been disturbed, however, first loosen the locknut and unscrew the throttle stop screw until it no longer touches the throttle lever. Now, turn the screw until it makes just contact with the lever. Turn in a further 1 ¼ turns, holding this in place tighten the locknut up securely. To remove and install, loosen the hose clamps and detach the air inlet hose, the resonator (if fitted) between the throttle body and air cleaner. For the throttle position sensor and ISC motor, disconnect the wiring. For the 2.4 litre models, disconnect the throttle control motor wiring connector. Remove the coolant and vacuum hoses from the throttle body and seal the coolant hoses to prevent dirt entry and coolant loss. Open the throttle lever manually if it is suitable then disconnect the inner throttle cable. To remove throttle body from the plenum chamber, undo the retaining bolts noting the direction of installation of the gasket. Discard the gasket. Remove ISC body from throttle body by unscrewing the retaining screws on all but the 2.4 litre models. Use throttle body or carburetor cleaner to clean the throttle body thoroughly, especially the throttle valve and idle passages, avoiding the ISC body to avoid damaging the wax pellet inside. Prevent the cleaner from entering the throttle shaft bearings and for 2.4 litre models also ensure the cleaner does not flow towards the throttle control motor. Operate throttle lever and check smooth working, whether it closes completely without sticking when released, lubricate throttle shaft with a small quantity of machine oil. The installation is a reversal of the removal. Ensure that the mating faces of the plenum chamber, throttle body and ISC body, are free of old gasket material. If necessary, install a new gasket and secure the ISC body to the throttle body by tightening the retaining screws. Using a new gasket in the noted position, install the throttle body to the plenum chamber and tighten the retaining bolts to the specified torque. For all models except those with a 2.4 litre engine, pull the throttle lever by hand and connect the inner throttle cable. Reconnect the vacuum and coolant hoses to the throttle body. Also, connect the wiring to the throttle position sensor and ISC motor or throttle control motor. Ensure the throttle cable and coolant level is adjusted and topped up as necessary.

Genuine Mitsubishi Throttle Body

Fuel Injection Throttle Body

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

13 Throttle Bodies found

View related parts
Mitsubishi Throttle Body Part Number: 1450A233
$768.32 MSRP: $1001.73
You Save: $233.41 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Throttle Body Assembly
Fits the following Mitsubishi Models:
- Eclipse Cross | 2022-2024, 2018-2020 | ES, LE, SE, SE Special Edition, SEL, SEL Special Edition, SEL Touring, SP | 4 Cyl 1.5 L GAS
View related parts
Mitsubishi Throttle Body Part Number: 1450A258
$771.51 MSRP: $1005.88
You Save: $234.37 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Throttle Body Assembly
Fits the following Mitsubishi Models:
- Outlander PHEV | 2023-2024 | ES, Platinum Edition, Ralliart, SE, SE Tech, SEL, SEL Premium, SEL Touring | 4 Cyl 2.4 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Mitsubishi Throttle Body Part Number: MD369615
$829.01 MSRP: $1080.85
You Save: $251.84 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Throttle Body Assembly
Fits the following Mitsubishi Models:
- Montero Sport | 2004 | LS, XLS | 6 Cyl 3.5 L GAS
View related parts
Mitsubishi Throttle Body Part Number: 1450A101
$903.76 MSRP: $1178.31
You Save: $274.55 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Electronic Fuel Injection Throttle Body Assembly
Fits the following Mitsubishi Models:
- Lancer | 2008-2012 | DE, ES, ES Sportback, GT, GT Sportback, GTS, GTS Sportback, SE | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
- Outlander | 2008-2012 | ES, SE | 4 Cyl 2.4 L GAS
- Outlander Sport | 2011-2012 | ES, SE | 4 Cyl 2.0 L GAS
View More
View related parts
Mitsubishi Throttle Body Part Number: 1450A205
$977.16 MSRP: $1274.00
You Save: $296.84 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Throttle Body Assembly
Fits the following Mitsubishi Models:
- Outlander | 2014-2020 | GT | 6 Cyl 3.0 L GAS
View related parts
Mitsubishi Throttle Body Part Number: 1450A109
$980.50 MSRP: $1278.35
You Save: $297.85 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Throttle Body Assembly
Fits the following Mitsubishi Models:
- Lancer | 2008-2015 | Evolution Final Edition, Evolution GSR, Evolution MR, Evolution MR Touring, Evolution SE, Ralliart, Ralliart Sportback | 4 Cyl 2.0 L GAS
View related parts
Mitsubishi Throttle Body Part Number: 1450A148
$1018.16 MSRP: $1327.46
You Save: $309.30 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Throttle Body Assembly
Fits the following Mitsubishi Models:
- Outlander | 2010-2013 | GT, XLS | 6 Cyl 3.0 L GAS
View related parts
Mitsubishi Throttle Body Part Number: MQ721963
$1024.58 MSRP: $1335.83
You Save: $311.25 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Throttle Body Assembly
- Replaced by: MQ727348
Fits the following Mitsubishi Models:
- Outlander | 2022-2024 | Black Edition, ES, SE, SE Launch Edition, SEL, SEL Launch Edition | 4 Cyl 2.5 L GAS
View related parts
Mitsubishi Throttle Body Part Number: 1450A195
$1040.44 MSRP: $1356.50
You Save: $316.06 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Throttle Body Assembly; Fuel Injection Throttle Body Assembly; Fuel Injection ETB Assembly
Fits the following Mitsubishi Models:
- Lancer | 2013-2017 | DE, ES, ES Sportback, GT, GT Sportback, SE, SEL | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
- Outlander | 2013-2020 | ES, LE, SE, SEL, SP | 4 Cyl 2.4 L GAS
- Outlander PHEV | 2018-2021 | GT, LE, SEL | 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 4 Cyl 2.4 L PLUG-IN HYBRID EV-GAS (PHEV)
- Outlander Sport | 2013-2024 | BE, ES, GT, GT Special Edition, LE, Ralliart, S, SE, SE Special Edition, SEL, SP, Trail Edition | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View More
View related parts
Mitsubishi Throttle Body Part Number: 1450A193
$1040.44 MSRP: $1356.50
You Save: $316.06 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Throttle Body Assembly
Fits the following Mitsubishi Models:
- Mirage | 2017-2024, 2014-2015 | BE, Black Edition, Carbonite Edition, DE, ES, GT, LE, RF, SE | 3 Cyl 1.2 L GAS
- Mirage G4 | 2017-2024 | BE, Carbonite Edition, ES, LE, RF, SE | 3 Cyl 1.2 L GAS
View related parts
Mitsubishi Throttle Body Part Number: MN130069
$1091.39 MSRP: $1422.94
You Save: $331.55 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Throttle Body Assembly
Fits the following Mitsubishi Models:
- Montero | 2004-2006 | Limited, XLS | 6 Cyl 3.8 L GAS
View related parts
Mitsubishi Throttle Body Part Number: MN135985
$1151.09 MSRP: $1500.77
You Save: $349.68 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Electronic Fuel Injection Throttle Body Assembly
Fits the following Mitsubishi Models:
- Eclipse | 2006-2012 | GS, GS Sport, SE, Spyder GS, Spyder GS Sport, Spyder SE | 4 Cyl 2.4 L GAS
- Galant | 2004-2012 | DE, ES, FE, SE, Sport Edition | 4 Cyl 2.4 L GAS
- Lancer | 2004-2006 | Ralliart, Sportback, Sportback Ralliart | 4 Cyl 2.4 L GAS
- Outlander | 2004-2006 | LS, Limited, SE, XLS | 4 Cyl 2.4 L GAS
View More
View related parts
Mitsubishi Throttle Body Part Number: 1450A102
$1542.28 MSRP: $1867.17
You Save: $324.89 (18%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Throttle Body Assembly
Fits the following Mitsubishi Models:
- Outlander | 2007-2009 | ES, LS, XLS | 6 Cyl 3.0 L GAS

Mitsubishi Throttle Body

The Mitsubishi Throttle Body is the precise air gate that allows your engine to breathe in accordance with your right foot. A compact assembly houses a butterfly plate. This butterfly plate tilts open on pressing the accelerator, and a position sensor reports the angle at which it has tilted. The computer then matches the fuel flow accordingly. This maintains a steady idle as well as sharp response. The routine Throttle Body inspection removes carbon build-up and maintains accurate sensor readings. In addition, the idle bypass passage allows just the right amount of air during stoplight pauses to ultimately promote long-term reliability. Because of the integration of airflow metering and high-response digital feedback in the unit, emissions levels remain low, cold starts easy, and confidence high throughout the range. Mitsubishi develops practical and clever cars in addition to this smart component. It has been producing lightweight vehicles for many decades now and hasn't forgotten its Model A roots, nor has it diverted too far from that focus, considering its recent crossovers. They also use Mitsubishi's MIVEC engines that are economy efficient and offer impressive punch, add Super All Wheel Control to help deliver traction on gravel or snow, and offer driver assist technology like cruise control, smartphone link, and more that teens and parents can use with zero fuss. The offering of plug-in hybrids reflects the brand's commitment to versatile propulsion, while continued research with fuel cells hints at future developments. All vehicles strive for balanced handling, user-friendly cabins, and dependable performance, all qualities that align perfectly with the responsive management that the Mitsubishi Throttle Body delivers across all gasoline-powered models.

Pick genuine OEM Throttle Body if you want superb performance and durability that lasts. Mitsubishi builds that using high-grade materials and official factory techniques to meet very strict standards. This means you get parts you can actually trust for your daily drive. Finding the right parts is simple in the massive stock of genuine inventory. You can stop guessing if a part will fit or hold up. You will love the low prices, dependable service and the real manufacturer's warranty on Mitsubishi Throttle Body. Order today and the store will ship your brand-new items to your door as fast as possible.

Mitsubishi Throttle Body Parts Questions & Experts Answers

Throttle Body
MN135985
Q: How to adjust and reinstall the throttle stop screw and throttle body on 1.5 litre and 2.4 litre on Mitsubishi Lancer?
A:
On 1.5 litre models, a factory set throttle stop screw is supplied, which is not supplied on other models. Typically, you should not have to make any adjustment to this screw. If it has been disturbed, however, first loosen the locknut and unscrew the throttle stop screw until it no longer touches the throttle lever. Now, turn the screw until it makes just contact with the lever. Turn in a further 1 ¼ turns, holding this in place tighten the locknut up securely. To remove and install, loosen the hose clamps and detach the air inlet hose, the resonator (if fitted) between the throttle body and air cleaner. For the throttle position sensor and ISC motor, disconnect the wiring. For the 2.4 litre models, disconnect the throttle control motor wiring connector. Remove the coolant and vacuum hoses from the throttle body and seal the coolant hoses to prevent dirt entry and coolant loss. Open the throttle lever manually if it is suitable then disconnect the inner throttle cable. To remove throttle body from the plenum chamber, undo the retaining bolts noting the direction of installation of the gasket. Discard the gasket. Remove ISC body from throttle body by unscrewing the retaining screws on all but the 2.4 litre models. Use throttle body or carburetor cleaner to clean the throttle body thoroughly, especially the throttle valve and idle passages, avoiding the ISC body to avoid damaging the wax pellet inside. Prevent the cleaner from entering the throttle shaft bearings and for 2.4 litre models also ensure the cleaner does not flow towards the throttle control motor. Operate throttle lever and check smooth working, whether it closes completely without sticking when released, lubricate throttle shaft with a small quantity of machine oil. The installation is a reversal of the removal. Ensure that the mating faces of the plenum chamber, throttle body and ISC body, are free of old gasket material. If necessary, install a new gasket and secure the ISC body to the throttle body by tightening the retaining screws. Using a new gasket in the noted position, install the throttle body to the plenum chamber and tighten the retaining bolts to the specified torque. For all models except those with a 2.4 litre engine, pull the throttle lever by hand and connect the inner throttle cable. Reconnect the vacuum and coolant hoses to the throttle body. Also, connect the wiring to the throttle position sensor and ISC motor or throttle control motor. Ensure the throttle cable and coolant level is adjusted and topped up as necessary.