How to diagnose and replace a brake light switch on Mitsubishi Galant?

The brake light switch is found on the mounting bracket for the brake pedal, and it activates the rear brake light when pressed. Disengaging the left-side under-dash panel and the heater/air conditioning duct allows access to the switch. First of all, you might want to check the fuse if the brake lights are out. If the fuse is still intact, then voltage will need to be checked on the feed wire to the switch, and if no voltage is found, then the wire from the switch to the fuse box will need some work done on it. When the brake is engaged, the terminal wire at the brake switch output should show voltage if voltage is present; replace the switch if it does not. When the voltage is confirmed, check for power on the brake light wires at the tail light housings while the brake pedal is pressed. If voltage is not present, the circuit between the switch and brake lights needs to be repaired. When you feel voltage present, a bad ground is checked by probing the ground wire terminal at the tail light connector with a jumper wire arranged with a good ground; when the brake lights activate, repair the ground circuit. It would be prudent to consider that, although unlikely, all of the brake light bulbs are burned out. The electric connector from the brake light switch should be disengaged for replacement and adjustment. With respect to models manufactured in 1998 or earlier, the switch can be taken off by loosening the locknut and taking it off the bracket. To reinstall, perform the reverse. The switch should be set such that a gap of 0.020 to 0.040 inches (0.51 to 1.02 mm) exists between the switch body and brake pedal before locking the nut firmly. On models from 1999 and onwards, the turn switch should be turned counter-clockwise to unlock the switch from its holder and pulled out. To install, insert the switch into its holder at a slight counterclockwise angle until the switch contacts the bracket on the brake pedal, then pull the switch straight back until there is approximately 3/64 inch clearance on the switch from the bracket. Then, rotate the switch clockwise until it locks in place and plug the electrical connector into the switch.

How to access and test A/C Switch, Brake Light Switch, Hazard Warning Switch and Relay on Mitsubishi Lancer?

Most switches have three or more wires; one from power, one taking power to the component or relay, possibly another one for illumination which may necessitate a fourth wire to earth the bulb. To get to the switch, you must take off the component it is fixed on. Observe the wire colors joining the power source to the switch and that of the switch to the component. Utilize an ohmmeter to measure resistance across the terminals after disconnecting the wire, the switch should show no resistance in On position and open circuit in Off position. A relay is basically an electrical switch that is operated by the aid of a remote signal. That is, a relay can carry a bigger current than a small switch. Thus the relay has the advantage of not needing heavy-duty switches and thick wires. The contacts in the relay are closed by a solenoid when the component switch is ON to allow power flow. In the engine compartment fuse and relay box as well as under the dashboard, there are various relays. Due to different equipment levels, not all vehicles are fitted with all the relays. To test to check a relay, first remove it from its housing. Then use an ohmmeter to check the continuity between the terminals. Next apply battery power to the relay and check its functionality. A combination switch is a single unit that contains a headlamp and turn signal lamp switch on one side and a wiper and washer switch on the other side. These switches have individual component parts that can be re-newed. To remove and install the steering column, adjust the steering column out of the way. Remove the steering column retaining screws. Disconnect the steering column wiring. Perform the above steering column removal and installation procedures for the CE, CG and CH. The removal and installation procedures for the Hazard Warning Switch and ventilation control switches also include details on the wiring. The lower dash panel contains the rheostat, which requires removal of the panel for access. The reverse lamp switch is incorporated into the inhibitor switch on automatic models, while on manual models, the functionality of the switch should be checked and renewed if necessary. The Brake Light Switch requires tests, adjustments and renewals and handbrake warning lamp switch needs tests and retire if needed. The removal and installation of courtesy lamp switches in the doors and tailgates need to be done carefully so the wiring can connect securely.

Genuine Mitsubishi Brake Light Switch

Brake Lamp Switch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

18 Brake Light Switches found

View related parts
Mitsubishi Control Module Part Number: 4815A165
$411.54 MSRP: $581.26
You Save: $169.72 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Control Unit, Parking BR; Brake Light Switch; Parking Brake Warning Switch; Module
Fits the following Mitsubishi Models:
- Eclipse Cross | 2018-2020 | SE, SEL | 4 Cyl 1.5 L GAS
- Outlander | 2018-2020 | ES, GT, LE, SE, SEL, SP | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS
- Outlander PHEV | 2018-2022 | GT, LE, SEL | 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 4 Cyl 2.4 L PLUG-IN HYBRID EV-GAS (PHEV)
View More
View related parts
Mitsubishi Parking Brake Switch Part Number: 8606A033
$106.12 MSRP: $147.39
You Save: $41.27 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch, Parking Brake; Brake Light Switch; Parking Brake Warning Switch; Switch
Fits the following Mitsubishi Models:
- Eclipse Cross | 2022-2025, 2018-2020 | SE, SE Special Edition, SEL, SEL Special Edition, SEL Touring | 4 Cyl 1.5 L GAS
- Outlander | 2017-2020 | ES, GT, LE, SE, SEL, SP | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS
- Outlander PHEV | 2018-2022 | GT, LE, SEL | 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 4 Cyl 2.4 L PLUG-IN HYBRID EV-GAS (PHEV)
View More
View related parts
Mitsubishi Parking Brake Warning Switch Part Number: 4815A049
$13.56 MSRP: $17.65
You Save: $4.09 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch, Parking Brake; Brake Light Switch; Switch
Fits the following Mitsubishi Models:
- Lancer | 2008-2016 | DE, ES, ES Sportback, Evolution GSR, Evolution MR, Evolution MR Touring, Evolution SE, GT, GT Sportback, GTS, GTS Sportback, Ralliart, Ralliart Sportback, SE, SEL | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
- Outlander | 2007-2018 | ES, GT, LE, LS, SE, SEL, XLS | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS
- Outlander PHEV | 2018 | GT, SEL | 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV)
- Outlander Sport | 2011-2024 | BE, ES, GT, GT Special Edition, LE, Ralliart, S, SE, SE Special Edition, SEL, SP, Trail Edition | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View More
View related parts
Mitsubishi Parking Brake Warning Switch Part Number: 4815A077
$18.57 MSRP: $24.18
You Save: $5.61 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch, Parking Brake; Brake Light Switch; Parking Brake Switch
Fits the following Mitsubishi Models:
- Mirage | 2017-2024, 2014-2015 | BE, Black Edition, Carbonite Edition, DE, ES, GT, LE, RF, SE | 3 Cyl 1.2 L GAS
- Mirage G4 | 2017-2024 | BE, Carbonite Edition, ES, LE, RF, SE | 3 Cyl 1.2 L GAS
View related parts
Mitsubishi Parking Brake Warning Switch Part Number: 4815A164
$334.02 MSRP: $471.79
You Save: $137.77 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Control Unit, Parking BR; Brake Light Switch; Control Module; Module
Fits the following Mitsubishi Models:
- Outlander | 2017-2018 | ES, GT, LE, SE, SEL | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS
- Outlander PHEV | 2018 | GT, SEL | 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Mitsubishi Stoplamp Switch Part Number: 25320W030P
$52.25 MSRP: $72.57
You Save: $20.32 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch, Stop Lamp; Brake Light Switch
- Replaces: 8614A111
Fits the following Mitsubishi Models:
- Eclipse Cross | 2022-2024, 2018-2020 | ES, LE, SE, SE Special Edition, SEL, SEL Special Edition, SEL Touring | 4 Cyl 1.5 L GAS
- Mirage | 2022-2024 | BE, Black Edition, ES, LE, SE | 3 Cyl 1.2 L GAS
- Mirage G4 | 2022-2024 | BE, ES, LE, SE | 3 Cyl 1.2 L GAS
- Outlander | 2010-2020 | ES, GT, LE, SE, SEL, SP, XLS | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS
- Outlander PHEV | 2018-2021 | GT, LE, SEL | 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 4 Cyl 2.4 L PLUG-IN HYBRID EV-GAS (PHEV)
- Outlander Sport | 2017-2021, 2011-2014 | ES, GT, LE, SE, SEL, SP | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View More
View related parts
Mitsubishi Stoplamp Switch Part Number: 25320W040P
$55.44 MSRP: $77.00
You Save: $21.56 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch, Stop Lamp; Brake Light Switch
- Replaces: 25320W010P
Fits the following Mitsubishi Models:
- Outlander Sport | 2022-2024 | ES, GT, GT Special Edition, LE, Ralliart, S, SE, SE Special Edition, SEL, Trail Edition | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View related parts
Mitsubishi Stoplamp Switch Part Number: MB596608
$62.18 MSRP: $86.37
You Save: $24.19 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch, Stop Lamp; Brake Light Switch; Stoplight Switch; Release Switch; Brake Switch; Brake Pedal Switch
Fits the following Mitsubishi Models:
- 3000GT | 1991-1999 | Base, SL, Spyder SL, Spyder VR-4, VR-4 | 6 Cyl 3.0 L GAS
- Cordia | 1985-1988 | L, Turbo | 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS
- Diamante | 1992-1998 | ES, LS | 6 Cyl 3.0 L GAS, 6 Cyl 3.5 L GAS
- Eclipse | 1990-1999 | Base, GS, GST, GSX, RS, Spyder GS, Spyder GST | 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
- Expo | 1992-1995 | Base, SP | 4 Cyl 2.4 L GAS
- Expo LRV | 1992-1994 | Base, Sport | 4 Cyl 1.8 L GAS, 4 Cyl 2.4 L GAS
- Galant | 1989-1998, 1985-1987 | Base, DE, ES, GS, GSR, GSX, LS, S, VR-4 | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
- Mighty Max | 1991-1996, 1987-1989 | 1 Ton, Base, SPX, Sport | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS, 4 Cyl 2.6 L GAS, 6 Cyl 3.0 L GAS
- Mirage | 1989-2002 | Base, DE, ES, GS, LS, RS, S, SE, Turbo, VL | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS, 4 Cyl 1.8 L GAS
- Montero | 1987-2002 | Base, LS, Limited, RS, SP, SR, Sport, XLS | 4 Cyl 2.6 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.5 L GAS
View More
View related parts
Mitsubishi Stoplamp Switch Part Number: 8614A283
$64.09 MSRP: $85.49
You Save: $21.40 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch, Stop Lamp; Brake Light Switch
Fits the following Mitsubishi Models:
- Outlander | 2022-2024 | Black Edition, ES, SE, SE Launch Edition, SEL, SEL Launch Edition | 4 Cyl 2.5 L GAS
- Outlander PHEV | 2023-2024 | ES, Platinum Edition, Ralliart, SE, SE Tech, SEL, SEL Premium, SEL Touring | 4 Cyl 2.4 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Mitsubishi Parking Brake Warning Switch Part Number: MR307076
$6.46 MSRP: $8.42
You Save: $1.96 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch, Parking Brake; Brake Light Switch
Fits the following Mitsubishi Models:
- Montero | 2003-2006 | Limited, XLS | 6 Cyl 3.8 L GAS
View related parts
Mitsubishi Parking Brake Warning Switch Part Number: MN102888
$12.21 MSRP: $15.90
You Save: $3.69 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch, Parking Brake; Brake Light Switch
Fits the following Mitsubishi Models:
- Endeavor | 2010-2011, 2004-2008 | LS, Limited, SE, XLS | 6 Cyl 3.8 L GAS
View related parts
Mitsubishi Parking Brake Warning Switch Part Number: MB277887
$13.18 MSRP: $17.17
You Save: $3.99 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch, Parking Brake; Brake Light Switch
Fits the following Mitsubishi Models:
- Eclipse | 1990-1994 | Base, GS, GST, GSX | 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS
- Mirage | 1989-1992 | Base, GS, LS, RS, SE, Turbo, VL | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS
- Sigma | 1989-1990 | Base | 6 Cyl 3.0 L GAS
View More
View related parts
Mitsubishi Stoplamp Switch Part Number: MB435457
$19.47 MSRP: $25.36
You Save: $5.89 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch, Clutch, Others; Clutch Pedal Position Switch; Brake Light Switch; Clutch Switch; Release Switch; Brake Switch
Fits the following Mitsubishi Models:
- 3000GT | 1991-1999 | Base, SL, Spyder SL, Spyder VR-4, VR-4 | 6 Cyl 3.0 L GAS
- Cordia | 1984-1985 | Base, L, LS, Turbo | 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS
- Diamante | 1992 | ES, LS | 6 Cyl 3.0 L GAS
- Eclipse | 1990-1999 | Base, GS, GST, GSX, RS, Spyder GS, Spyder GST | 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
- Expo | 1992-1995 | Base, SP | 4 Cyl 2.4 L GAS
- Expo LRV | 1992-1994 | Base, Sport | 4 Cyl 1.8 L GAS, 4 Cyl 2.4 L GAS
- Galant | 1989-1998, 1985 | Base, DE, ES, GS, GSR, GSX, LS, S, VR-4 | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
- Lancer | 2002-2017 | DE, ES, ES Sportback, Evolution GSR, Evolution MR, Evolution MR Touring, Evolution SE, GT, GT Sportback, GTS, GTS Sportback, LS, OZ Rally, Ralliart, Ralliart Sportback, SE, SEL | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
- Mighty Max | 1984-1996 | 1 Ton, Base, S, SP, SPX, Sport | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L DIESEL, 4 Cyl 2.4 L GAS, 4 Cyl 2.6 L GAS, 6 Cyl 3.0 L GAS
- Mirage | 1985-2002 | Base, DE, ES, GS, L, LS, RS, S, SE, Turbo, VL | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS, 4 Cyl 1.8 L GAS
View More
View related parts
Mitsubishi Stoplamp Switch Part Number: 8614A208
$21.56 MSRP: $28.07
You Save: $6.51 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch, Stop Lamp; Brake Light Switch
Fits the following Mitsubishi Models:
- Mirage | 2017-2019, 2014-2015 | DE, ES, GT, LE, RF, SE | 3 Cyl 1.2 L GAS
- Mirage G4 | 2017-2019 | ES, RF, SE | 3 Cyl 1.2 L GAS
View related parts
Mitsubishi Stoplamp Switch Part Number: 8614A041
$25.38 MSRP: $33.05
You Save: $7.67 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch, Stop Lamp; Brake Light Switch
Fits the following Mitsubishi Models:
- Eclipse | 2006-2012 | GS, GS Sport, GT, SE, Spyder GS, Spyder GS Sport, Spyder GT, Spyder SE | 4 Cyl 2.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Mitsubishi Stoplamp Switch Part Number: MR228924
$28.04 MSRP: $36.52
You Save: $8.48 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch, Stop Lamp, Others; Brake Light Switch; Clutch Switch
Fits the following Mitsubishi Models:
- Eclipse | 2006-2012 | GS, GS Sport, GT, SE, Spyder GS, Spyder GS Sport, Spyder GT, Spyder SE | 4 Cyl 2.4 L GAS, 6 Cyl 3.8 L GAS
- Lancer | 2002-2016 | DE, ES, ES Sportback, Evolution, Evolution GSR, Evolution MR, Evolution MR Touring, Evolution RS, Evolution SE, GT, GT Sportback, GTS, GTS Sportback, LS, OZ Rally, Ralliart, Ralliart Sportback, SE, SEL, Sportback, Sportback Ralliart | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
- Outlander | 2005-2006 | LS, Limited, SE, XLS | 4 Cyl 2.4 L GAS
View More
View related parts
Mitsubishi Stoplamp Switch Part Number: 8614A183
$29.79 MSRP: $38.78
You Save: $8.99 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch, Stop Lamp; Brake Light Switch; Brake Switch
Fits the following Mitsubishi Models:
- Diamante | 1999-2004 | Base, ES, LS, VR-X | 6 Cyl 3.5 L GAS
- Lancer | 2002-2017 | DE, ES, ES Sportback, Evolution, Evolution GSR, Evolution MR, Evolution MR Touring, Evolution RS, Evolution SE, GT, GT Sportback, GTS, GTS Sportback, LS, OZ Rally, Ralliart, Ralliart Sportback, SE, SEL, Sportback, Sportback Ralliart | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
- Mirage | 2017-2021, 2014-2015 | Carbonite Edition, DE, ES, GT, LE, RF, SE | 3 Cyl 1.2 L GAS
- Mirage G4 | 2017-2021 | Carbonite Edition, ES, LE, RF, SE | 3 Cyl 1.2 L GAS
- Montero | 2003-2006 | Limited, XLS | 6 Cyl 3.8 L GAS
- Outlander | 2003-2009 | ES, LS, Limited, SE, XLS | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS
View More
View related parts
Mitsubishi Stoplamp Switch Part Number: 8614A168
$33.38 MSRP: $43.80
You Save: $10.42 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch, Stop Lamp; Brake Light Switch
Fits the following Mitsubishi Models:
- Outlander Sport | 2015-2021 | BE, ES, GT, LE, S, SE, SEL, SP | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS

Mitsubishi Brake Light Switch

The Mitsubishi Brake Light Switch completes the circuit to light up the rear lamps when the driver taps the pedal, warning following traffic and further enhancing safety. Since 1870, the Mitsubishi group has been involved in smart and dependable mobility. From the early Model A sedan to modern vehicles equipped with MIVEC engines, Super All Wheel Control for assured grip, and convenient cruise control with smartphone link that ensures easy driving daily. The firm examines both the fuel cell and plug-in hybrid power so that future drivers can expect cleaner trips, while each model features easy maintenance, solid build quality, and functionalities within the understanding of young drivers. The dedication to simple engineering dictates the design of every component, including the compact Brake Light Switch above the pedal arm. The resting position of the spring-loaded plunger touches the pedal and keeps the circuit open, so when you press the pedal, the plunger releases and the circuit closes so that the bulbs shine all at once. As the device is mounted on a protected bracket with a single connector, it is resistant to road vibration and can also be easily accessed for routine inspection. This reflects the brand's goal of user-friendly design. Through regular inspections, it can ensure that the lighting works the moment the Brake Light Switch responds and that the rear lighting system is as reliable as the responsive handling of a Mitsubishi vehicle as it journeys through the city's crowded streets.

Pick genuine OEM Brake Light Switch if you want superb performance and durability that lasts. Mitsubishi builds that using high-grade materials and official factory techniques to meet very strict standards. This means you get parts you can actually trust for your daily drive. Finding the right parts is simple in the massive stock of genuine inventory. You can stop guessing if a part will fit or hold up. You will love the low prices, dependable service and the real manufacturer's warranty on Mitsubishi Brake Light Switch. Order today and the store will ship your brand-new items to your door as fast as possible.

Mitsubishi Brake Light Switch Parts Questions & Experts Answers

Stoplamp Switch
MB435457
Q: How to diagnose and replace a brake light switch on Mitsubishi Galant?
A:
The brake light switch is found on the mounting bracket for the brake pedal, and it activates the rear brake light when pressed. Disengaging the left-side under-dash panel and the heater/air conditioning duct allows access to the switch. First of all, you might want to check the fuse if the brake lights are out. If the fuse is still intact, then voltage will need to be checked on the feed wire to the switch, and if no voltage is found, then the wire from the switch to the fuse box will need some work done on it. When the brake is engaged, the terminal wire at the brake switch output should show voltage if voltage is present; replace the switch if it does not. When the voltage is confirmed, check for power on the brake light wires at the tail light housings while the brake pedal is pressed. If voltage is not present, the circuit between the switch and brake lights needs to be repaired. When you feel voltage present, a bad ground is checked by probing the ground wire terminal at the tail light connector with a jumper wire arranged with a good ground; when the brake lights activate, repair the ground circuit. It would be prudent to consider that, although unlikely, all of the brake light bulbs are burned out. The electric connector from the brake light switch should be disengaged for replacement and adjustment. With respect to models manufactured in 1998 or earlier, the switch can be taken off by loosening the locknut and taking it off the bracket. To reinstall, perform the reverse. The switch should be set such that a gap of 0.020 to 0.040 inches (0.51 to 1.02 mm) exists between the switch body and brake pedal before locking the nut firmly. On models from 1999 and onwards, the turn switch should be turned counter-clockwise to unlock the switch from its holder and pulled out. To install, insert the switch into its holder at a slight counterclockwise angle until the switch contacts the bracket on the brake pedal, then pull the switch straight back until there is approximately 3/64 inch clearance on the switch from the bracket. Then, rotate the switch clockwise until it locks in place and plug the electrical connector into the switch.
Stoplamp Switch
8614A183
Q: How to access and test A/C Switch, Brake Light Switch, Hazard Warning Switch and Relay on Mitsubishi Lancer?
A:
Most switches have three or more wires; one from power, one taking power to the component or relay, possibly another one for illumination which may necessitate a fourth wire to earth the bulb. To get to the switch, you must take off the component it is fixed on. Observe the wire colors joining the power source to the switch and that of the switch to the component. Utilize an ohmmeter to measure resistance across the terminals after disconnecting the wire, the switch should show no resistance in On position and open circuit in Off position. A relay is basically an electrical switch that is operated by the aid of a remote signal. That is, a relay can carry a bigger current than a small switch. Thus the relay has the advantage of not needing heavy-duty switches and thick wires. The contacts in the relay are closed by a solenoid when the component switch is ON to allow power flow. In the engine compartment fuse and relay box as well as under the dashboard, there are various relays. Due to different equipment levels, not all vehicles are fitted with all the relays. To test to check a relay, first remove it from its housing. Then use an ohmmeter to check the continuity between the terminals. Next apply battery power to the relay and check its functionality. A combination switch is a single unit that contains a headlamp and turn signal lamp switch on one side and a wiper and washer switch on the other side. These switches have individual component parts that can be re-newed. To remove and install the steering column, adjust the steering column out of the way. Remove the steering column retaining screws. Disconnect the steering column wiring. Perform the above steering column removal and installation procedures for the CE, CG and CH. The removal and installation procedures for the Hazard Warning Switch and ventilation control switches also include details on the wiring. The lower dash panel contains the rheostat, which requires removal of the panel for access. The reverse lamp switch is incorporated into the inhibitor switch on automatic models, while on manual models, the functionality of the switch should be checked and renewed if necessary. The Brake Light Switch requires tests, adjustments and renewals and handbrake warning lamp switch needs tests and retire if needed. The removal and installation of courtesy lamp switches in the doors and tailgates need to be done carefully so the wiring can connect securely.