Question 1

What are the steps and tools necessary for replacing spark plugs on Mitsubishi Galant?

Accepted Answer

Spark plugs are in the cylinder heads and accessed through long tubes in the top of the valve cover(s). Typically, you will require a spark plug socket that goes onto a ratchet and a range of extensions. Using a feeler gauge to check and adjust the spark plug gap can also be handy. A special tool for removing the plug wire can help to separate the wire boot from the spark plug but is not essential. Because of the aluminum cylinder head(s), spark plugs must be tightened using a torque wrench. You should get new spark plugs ahead of time and gap them to spec. Remove one plug at a time, install the correct replacement, and reconnect the plug to the engine before continuing. Let the engine completely cool down before removing any of the plugs during which time you can check the new plugs for defects and check the gaps. A suitable thickness gauge is used to check the gap between the electrodes at the plug tip. Adjustments are done wherever required. Do not check the gap on platinum- or iridium-tipped plugs. This may damage their coating. It is advisable to cover the fender with a protective material to prevent damage to the paint. The valve cover centre cover must be removed if applicable for 1994-1998 four-cylinder engines. Then the spark plug boot can be twisted and pulled off the spark plug. As one plug at a time is replaced, the wires won't get mixed up. On 1999 and later SOHC engines, the spark plug wires connect to coil-over spark plug units. Therefore, the wires must be detached from the coil pack before the plugs are removed. To gain access to the rear plug wires and access to the rear spark plugs on V6 engines, the upper intake manifold must be removed. Further, it is advisable to stuff clean rags in the lower intake manifold openings for security. First, detach any clips securing the wires of the spark plug. Second, twist to release the boot and pull it off. You can utilize compressed air to clear the dirt from the spark plug area and position the spark plug socket over the spark plug for removal. It is recommended to use anti-seize compound on new spark plugs. Use it sparingly on the threads so that the plugs will not seize in the aluminum cylinder head. Be careful not to apply any anti-seize on the electrode. To help prevent cross-threading, you can place a piece of rubber hose over the end of a spark plug to help align it with the hole. Once the spark plug has been installed and tightened to the proper torque specification, the plug wire or coil must be attached by twisting it until it is firmly seated. Continue in the same way with the rest of the spark plugs, replacing one at a time. For V6 models, before reinstallation of the upper intake manifold, the rags should be removed from the lower intake manifold.

Question 2

How to replace spark plugs on Mitsubishi Montero?

Accepted Answer

To change spark plugs, first, purchase them following the suggested maintenance schedule and make sure that these are the right type based on your engine as shown in the Emission Control Information label under the hood. Assemble the tools required, such as a spark plug socket, extensions, a gap gauge as well as a torque wrench. Never remove the engine until fully cooled, and observe the new plugs, and check the clearance between them with a type of wire gauge, so that there is a small drag between the electrodes. Take away the spark plug wire by pulling off the boot and blow away any debris in the spark plug hole with compressed air or a bicycle pump. With the spark plug socket, turn the old plug counterclockwise and remove it. Use reference images to compare the old plug with reference images to determine engine conditions. Insert a new plug into the hole by hand until it cannot be rotated further and then screw it in with a torque wrench or ratchet, with a short piece of rubber hose to help with this and avoiding cross-threading. Before connecting the spark plug wire to the new plug, verify that the spark plug wire is clean and then connect it to the new plug using a twisting action, repeat the process with the rest of the plugs and that they do not get mixed up.

Genuine Mitsubishi Spark Plug

31 Spark Plugs found

Mitsubishi Spark Plug Part Number: 1822A063

Mitsubishi Spark Plug Part Number: 1822A154

Mitsubishi Spark Plug Part Number: 1822A160

Mitsubishi Spark Plug Part Number: MS851357

Mitsubishi Spark Plug Part Number: 68303918AA

Mitsubishi Spark Plug Part Number: MN163235

Mitsubishi Spark Plug Part Number: MS851336

Mitsubishi Spark Plug Part Number: MR984943

Mitsubishi Spark Plug Part Number: MD378582

Mitsubishi Spark Plug Part Number: 1822A002

Mitsubishi Spark Plug Part Number: MN158596

Mitsubishi Spark Plug Part Number: 1822A011

Mitsubishi Spark Plug Part Number: 1822A021

Mitsubishi Spark Plug Part Number: MS851501

Mitsubishi Spark Plug Part Number: 1822A078

Mitsubishi Spark Plug Part Number: MD372553

Mitsubishi Spark Plug Part Number: MN163236

Mitsubishi Spark Plug Part Number: 1822A069

Mitsubishi Spark Plug Part Number: 1822A079

Mitsubishi Spark Plug Part Number: 1822A068

Mitsubishi Spark Plug

Mitsubishi Spark Plug Parts Questions & Experts Answers

Related Mitsubishi Parts

Browse by Model